Jäger Z62-M260.23 S5 Скачать руководство пользователя

Страница: 5 / 36

Transport and packaging

Item no. 10202024, Revision 02

5 ( 36 )

Transport and packaging

Avoid strong vibrations or impacts during transportation, as these could dam-
age the ball bearings of the HF spindle.

Any damage reduces the accuracy of the HF spindle.

Any damage restricts the functionality of the HF spindle.

Any damage shortens the service life of the HF spindle.

2.1

Scope of supply of HF spindle

The following parts are supplied with the HF spindle:

High Frequency Spindle

Jaw wrench

Hook wrench

Transport packaging

Check the high frequency spindle for completeness upon delivery.

2.1.1

Optional accessories

Available on request:

Spindle holder

Frequency converter

Collet

Felt cleaning taper

Collet grease

Further accessories on request.

Only approved accessories have been tested for operational safety and func-
tionality.

Do not use any other accessories – this may invalidate any warranty claims
and compensation claims for damages.

If the spindle holder is to be produced in-house, it is essential to contact

Alfred Jäger GmbH

before starting production to request the tolerances

and production plan for the spindle holder.

2.1.2

Documentation supplied

The documents listed below are supplied with the HF spindle:

Manual

The declaration of incorporation is part of the manual.

Inspection protocol

Check that the documentation supplied is complete when the spindle is
delivered. If necessary, request a new copy.

Содержание Z62-M260.23 S5





































Результаты поиска

Содержание Z62-M260.23 S5

Отзывы:

Похожие инструкции для Z62-M260.23 S5

Бренды по названию

Популярные бренды

Jäger Z62-M260.23 S5, Руководство пользователя

Результаты поиска

Содержание Z62-M260.23 S5

Отзывы:

Похожие инструкции для Z62-M260.23 S5

Бренды по названию

Популярные бренды