Jäger Z62-M260.23 S5 Скачать руководство пользователя

Страница: 4 / 36

Preliminary information

Item no. 10202024, Revision 02

4 ( 36 )

Preliminary information

The high frequency spindle (HF spindle) is a high quality precision tool for
high speed machining.

1.1

Purpose of the manual

The manual is an important component of the HF spindle.

Store the manual carefully.

Make the manual available to all persons who work with the HF spindle.

Read the documentation supplied in full.

Before carrying out any work, read the corresponding section of the man-
ual carefully again.

1.2

Explanation of symbols used

To enable quick classification of information, this manual uses visual aids in
the form of symbols and text markings.

Notes are marked with a signal word and a colored box:

DANGER

Dangerous situation!

Results in serious injury or death.

Measure to avert the danger.

WARNING

Dangerous situation!

May result in serious injury or death.

Measure to avert the danger.

CAUTION

Dangerous situation!

May result in minor to moderate injury.

Measure to avert the danger.

Note

May result in material damage. This warning symbol is not a warning for per-
sonal injury.

Tip

Tips indicate useful information for users.

Содержание Z62-M260.23 S5





































Результаты поиска

Содержание Z62-M260.23 S5

Отзывы:

Похожие инструкции для Z62-M260.23 S5

Бренды по названию

Популярные бренды

Jäger Z62-M260.23 S5, Руководство пользователя

Результаты поиска

Содержание Z62-M260.23 S5

Отзывы:

Похожие инструкции для Z62-M260.23 S5

Бренды по названию

Популярные бренды