Jadever JCL Series Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 30

background image

JADEVER SCALE CO., LTD

After finished grinding the scale, please install the upper cover, turn the scale upside down,

then tighten 4 fixing screws, and then cover the stainless weighing pan.

12. Switch on the scale, conduct calibration then check weighing functions.

Model

JCL-1.5K
JCL-3K
JCL-6K

JCL-7.5K

JCL-15K
JCL-30K

LC Max. capacity

(ZEMIC load cell)

3kg
5kg
10kg
10Kg
20Kg
40kg

LC Max. capacity

(MAVIN load cell)

3kg
4.5kg
7.5Kg
10Kg
20Kg
45Kg

6-3 Rechargeable Battery Replacement

1.Remove the stainless weighing pan. 2. Put the scale upside down, Loosen

and remove the screw on the battery cover.

3.Remove the battery cover. 4. Disconnect the wire connection then remove

the rechargeable battery.

5.Prepare for a new rechargeable 6. Put the rechargeable battery in the

battery and make sure the red end chamber with literal side upward and the

connected to red wired and black end wire to the right side.

connected to black wire.

24 JCL Service Manual

«
...
24
25
26
27
28
...
»

Содержание JCL Series































Отзывы:

Нет отзывов

Похожие инструкции для JCL Series

Бренд: CALIMA Страницы: 6

Бренд: Balance Страницы: 10

Бренд: Valore Страницы: 4

Бренд: T Scale Страницы: 4

Бренд: Tanita Страницы: 29

Бренд: Black & Decker Страницы: 12

Бренд: Buffalo Tools Страницы: 4

Бренд: Jadever Страницы: 4

Бренд: Jadever Страницы: 10

Бренд: Jadever Страницы: 17

Бренд: Tanita Страницы: 11

Бренд: Tanita Страницы: 13

Бренд: Tanita Страницы: 30

Бренд: Cardinal Страницы: 16

Бренд: Medisana Страницы: 64

Бренд: Thulos Страницы: 2

Бренд: TMT Страницы: 10

Бренд: Kalorik Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды