background image

6

SHUT OFF VALVE

WATER SUPPLY (3/8" COPPER TUBING)

Water Supply

Consult local authorities for plumbing code require-

ments in your area.  Connect house cold water supply to
steam generator supply tubing.

IMPORTANT:  Jacuzzi Whirlpool Bath does not

warrant connections of water supply fittings and
piping or drain systems.  Nor is it responsible for
damage to the shower base which occurs during
any installation procedure.

Base Drain

Remove the stainless steel strainer from the drain

assembly.  Disassemble the locknut and two gaskets
from the back of the drain assembly.  Apply a 1/4" bead
of caulking (silicone) to the drain hole and insert the drain
assembly.  Replace the rubber washer, fiber washer,
and lock nut in that order.  Hand  tighten the locknut.
Remove excess sealant from finished side.

Apply a lubricant (common household liquid soap

works well) to the inside of the rubber seal of the drain
assembly.
NOTE:  Watertight installation of the drain is the
installer's responsibility.  Drain leakage is excluded
from the Jacuzzi Whirlpool Bath warranty of this
product.

Slide the shower base into the framed opening and

attach the shower base flange to the stud wall and
blocking with screws provided.
NOTE:  If there is any gap between base flange and
stud or blocking, shims MUST be used to prevent
distortion or cracking of the flange.

STRAINER

DRAIN
ASSEMBLY

SILICONE
SEALANT

SHOWER
BASE

RUBBER WASHER

FIBER WASHER

NUT

APPLY
LUBRICANT

DRAIN ASSEMBLY

With a large screwdriver and the tool included with the

drain, tighten the inside compression nut to seal the
drain pipe connection.  After drain is fully installed, test
for proper drainage.  If the shower base does not drain
properly, rectify this condition before proceeding with
the installation.  Jacuzzi Whirlpool Bath is not respon-
sible for removal and/or reinstallation costs.

TIGHTEN SEALING NUT

TOOL
(INCLUDED)

Electrical Connections

A separate circuit is required.  Install a NEMA 6-50R

receptacle to the studwall at least 4 inches above the
floor.  The receptacle is not provided.

LOCATE RECEPTACLE IN THIS AREA.
RECPTACLE TO BE ACCESSIBLE
FROM SERVICE ACCESS

Содержание Steam & Shower Base SEDONA





















Отзывы: