47
Programming Instructions
Your Jacuzzi spa is equipped with setting menus that allow
you to program and activate different components of the spa.
With our ProTouch™ Glass control panel, programming your
spa has never been easier. In the sections that follow, we will
guide you through the process of programming the spa to fit
your personal comfort.
Heat and Filter:
Tap (
)
to access the
heating and filtration programming.
Water Care:
Tap (
)
to access the water
care programming.
Lock:
Tap (
)
to access the locking program-
ming.
Time and Date:
Tap (
)
to access the
time and date programming.
Language:
Tap (
)
access the language
programming.
Units:
Tap either
or
for the tempe-
rature display.
Default setting is
.
Wi-Fi:
Tap (
)
to access the Wi-Fi programming.
Back Button:
Tap to go back to the previous menu.
Invert Button:
Tap to invert the display image.
I
Programming the Heating Mode
Your Jacuzzi spa is equipped with 3 modes of heating.
An automatic mode called “Auto,” where the spa’s temperature
is maintained at all times. An energy saving heating cycle cal-
led “Econo.” A mode that will only activate the heater during the
daytime called “Day” mode.
Note:
The heater will activate when the temperature drops
~2° from the set temperature.
Indicates that the feature is active.
Indicates that the
feature is not active.
Auto heating:
When programmed to “Auto,” the spa will maintain the water
temperature to the set temperature. Heating will occur when
necessary.
To select this mode, tap (
)
next to the “Auto” icon.
Econo heating:
This is an energy saving heating program that allows the spa to
heat during non-peak hours. When programmed to “Econo,” the
spa will only be allowed to heat the water between 5:00 PM to
7:00 AM every day of the week. The hours cannot be adjusted.
To select this mode, tap (
)
next to the “Econo” icon.
Day heating:
When programmed to “Day,” the spa will only be allowed to
heat the water between 7:00 AM to 5:00 PM every day of the
week. The hours cannot be adjusted.
To select this mode, tap (
)
next to the “Day” icon.
I
Programming the Primary Filter
To access the “Primary Filter” feature, you need to use the Sli-
der Bar to scroll down to the “Heat & Filter” menu. Once you
scroll down, tap (
)
to enter the “Primary Filter” program-
ming.
During a primary filtration, the circulation pump, CLEARRAY
and ozone unit (if applicable) are activated. The factory default
cycle starts at 12:00 AM and last for 8 hours. If you elect to
keep this setting, then you can skip this section.
몇
In extreme bitter cold weather we recommend you
program the circulation pump to run 24 hours.
Refer to the "Winterizing" section.
Any time the circulation pump runs outside of a program cycle,
e.g. for heating, that run time will be deducted from the next
primary filter cycle. For example, the primary filter cycle is set to
8 hours every 24 hours but the circulation pump comes on for
2 hours to heat the water after the cycle has finished. The next
primary filter cycle will only be for 6 hours not 8 hours.
Water Care
WiFi
Heat & Filter
SETTINGS
>
>
>
96
6:45 PM
ON
UV
>
Heat & Filter
>
Water Care
>
Lock
>
Time & Date
>
Language
Cº
Fº
Units
Fº
>
WiFi
Econo
Day
Auto
HEAT & FILTER
>
Econo
Day
Auto
HEAT & FILTER
Primary Filter
Secondary Filter
HEAT & FILTER
>
>
Содержание J-500 Series
Страница 2: ......
Страница 3: ...Italiano Avvertenze 4 English Warnings 32 Fran ais Recommandations 59 Index...
Страница 90: ...90...
Страница 91: ...91...