47
CAUTION:
Never leave electrical devices in the Media Lock-
er when spa is not is use to prevent damage from outdoor el-
ements! Never spray Media Locker with a pressurized water
hose for any reason! Damage to the device or spa stereo system
caused by water intrusion is not covered under the manufactur-
er's warranty! Damage to Media Locker port or electrical devices
due to excessive force or improper alignment during installation
or removal from Media Locker is not covered under warranty.
Pairing the Remote and Stereo
In order for the remote to operate the stereo, you
need to pair them using the following method:
AUDIO
MODE
REPEAT
RANDOM
DIR -
DIR +
1
2
3
- Make sure the stereo unit is in "Standby" mode. LED power
light will be red.
- Press any button on the remote to turn it ON. The remote
LCD display will read “No Link.”
- Press and hold the “Mode” button on the remote. At the
same time, press and hold the power button on the stereo
for 2 seconds
- The remote LCD display will read “Welcome,” “Load” and “Ra-
dio” if the pairing sequence was successful.
Audio Settings
The Audio button, provides access to many of the stereo’s set-
tings. By continually pressing the Audio button you can scroll
and adjust the following functions: BAS-TRE-BAL-FAD-DSP-AR-
EA-LOUD-DX-STEREO (respectively).
Note:
You can adjust the settings by pressing the Audio button,
making your adjustments and pressing the Audio button to go the
next feature. If you exit the setting menus continually press the Au-
dio button until you reach the setting you would like to adjust.
Bass Setting
Press the Audio button once to access the bass set-
ting. The LCD display will change to “BAS 0,” Figure D.
Press the Up button to adjust the setting to a maxi-
mum of +5. Press the Down button to adjust the setting
down to -5.
Note:
The default setting is “0.” This feature is disabled when a “Dig-
ital Sound Processor” (DSP) setting is active such as “Rock,” “Classic,”
or “Pop.”
Treble Setting:
Press the Audio button 2 times to access the treble setting. The LCD
display will change to “TRE 0,”. Press the Up button to adjust the set-
ting to a maximum of +5. Press the Down button to adjust the set-
ting down to -5.
Note:
The default setting is “0.” This feature is disabled when a “Dig-
ital Sound Processor” (DSP) setting is active such as “Rock,” “Classic,”
or “Pop.”
Balance Setting
Press the Audio button 3 times to access the balance setting. The
LCD display will change to “BAL L=R,”. Press the Up button to ad-
just the setting to a maximum of 10R (only the right side speakers
will have volume). Press the Down button to adjust the setting
down to 10L (only the left side speakers will have volume).
Fade Setting
Press the Audio button 4 times to access the fade setting. The LCD
display will change to “FAD F=R,”. Press the Up button to adjust the set-
ting to a maximum of 10F (only the front speakers will have volume).
Press the Down button to adjust the setting down to 10R
(only the rear speakers will have volume).
Digital Sound Processor (DSP) Setting
Press the Audio button 5 times to access the DSP setting. The
LCD display will change to “DSP OFF”. Press the Up button to se-
lect one of the preset settings such as Rock, Classic or Pop.
ROCK
If a preset setting is select a small icon
will appear on the LCD display.
Area Setting
Press the Audio button 6 times to access the Area setting. The
LCD display will change to “AREA USA,”. Press the Up button to
select either USA or EUR setting.
Loud Setting
Press the Audio button 7 times to access the Loud setting. The
LCD display will change to “LOUD OFF”. Press the Up button to
select either OFF or ON.
Distant Setting:
Press the Audio button 8 times to access the Dis-
tant setting. The LCD display will change to “DX,”. Press
the Up button to select either Distant (DX) or Lo-
cal for station frequency. The “LOCAL” setting allows for
better FM reception when a local station is too strong. Leave
the setting to “DX” if this condition does not exist.
Stereo Setting:
Press the Audio button 9 times to access the Stereo setting. The
LCD display will change to “STEREO,” . Press the Up button to se-
lect either Stereo or Mono.
Wireless Remote Control Functions
A wireless radio frequency (RF) remote control is supplied
on all spas with the optional audio system. This remote provides
control of the radio and over some media device functions.
Содержание J-300 Series
Страница 2: ......
Страница 3: ...Italiano Avvertenze 4 English Warnings 28 Fran ais Recommandations 51...
Страница 79: ...79...
