background image

6

INSTALLATION

Equipment Set-Up

• Turn on circuit breakers at the main electrical panel.

• Select JETS on the SYSTEM switch.

• Add 

1

/

4

 cup sodium dichlor (a fast dissolving granu-

lar type of chlorine) to the water and let the whirlpool
run for 15-20 minutes only.

• Turn off JETS.

• Turn off circuit breakers.

Immediately  open the drain valve and drain the spa
completely.

CAUTION:  Leave the rigid cover off the spa during this
procedure. Do not use the spa during this procedure.
Drain the spa immediately afterward.

8. Close the drain valve and fill the spa with water to

approx. 7  inches below the spa rim, or to water line
indicator mark on the skimmer frame.  (See illustration
this page.)

9. Turn on circuit breakers at the main service panel.

10. Set the heater thermostat for the maximum tempera-

ture.

11. Test the spa for proper operation.  (Refer to Operating

Instructions.)

12. Refer to Water Quality section of the Operating Instruc-

tions.  Test for water quality, then add treatment chemi-
cals to ensure proper levels.

All Jacuzzi Whirlpool Bath spas are factory tested for proper
operation and water tight connections prior to shipping.  If
leaks or other malfunctions are detected, immediately
notify your Jacuzzi Whirlpool Bath dealer or Authorized
Service Agent, or call Jacuzzi Whirlpool Bath, (510) 938-
7070, or (510) 938-7411 for Warranty Service.

1. Remove the plastic sheet covering the spa.  Use care;

stepping into the spa with shoes will scratch the acrylic
surface.

2. Remove any packing materials from the spa.

3. Remove each filter cartridge from its plastic bag.

4. Pull open the skimmer/filter door by the handle located

in the middle of the door and remove the skimmer
basket.  Then insert the filter cartridge into the filter
housing and re-insert the basket so that it fits in place
over the filter cartridge, and close the skimmer/filter
door.

5. Clean the interior of the spa of any remaining construc-

tion debris.  Remove stubborn stains, paint, or tar with
turpentine, isopropyl alcohol or paint thinner.  A mild
liquid dishwashing detergent on a damp cloth is fine for
cleaning off other dirt.  Plaster can be removed by
scraping with a wooden edge; do not use a metal
scraper, wire brush, or other metal tools, as they will
damage the spa’s surface.

6. Install the skirt panel which was not installed on the spa

at the factory.  To do this, secure with the screws
provided in your spa accessory package and follow
instructions provided with panels.

7. On initial start-up, it is necessary to purge and sanitize

the system as stated below.

• Remove the optional spa cover completely.

• Close the drain valve on the suction plumbing.

• Open the six fully adjustable jets.

• Fill the spa with water to its normal operating level,

which is the water level indicator mark on the
skimmer/filter frame.

CONTROL PANEL WATER RAINBOW

SPOUT

SUCTION
COVERS

SKIMMER/
FILTERS

WATER LEVEL
MARK

SPA LIGHT

DIRECTIONALLY
ADJUSTABLE JET

FULLY
ADJUSTABLE
WHIRLPOOL
JET

SILENT AIR
CONTROLS

Содержание D550000
























Отзывы: