Jacobsen tournament cut 22 Скачать руководство пользователя | Manualshive

Страница: 22 / 84

background image

7 MAINTENANCE

GB-22

7.7

STORAGE________________________________________________________________

General

1.

Wash the mower thoroughly and lubricate. Repair
and paint damaged or exposed metal.

2.

Inspect the mower, tighten all hardware, replace
worn or damaged components.

3.

Clean the tires thoroughly and store the tractor on
the kickstand so the load is off the tires. The front
roller or Turf Groomer should be resting on a wood
board.

4.

Keep the machine and all its accessories clean, dry
and protected from the elements during storage.
Never store equipment near an open flame or spark
which could ignite fuel or fuel vapors.

Engine

1.

While the engine is warm, remove drain plug and
drain the oil from the crankcase. Install drain plug
and refill with fresh oil. Torque drain plug to 22 ft. lb.
(30 Nm).

2.

Clean exterior of engine. Paint exposed metal or
apply a light coat of rust preventative oil.

To prevent the build-up of gum residues and vanish
films, fill the tank with stabilized fuel. Use an anti-
oxidant fuel conditioner, such STA-BIL®. Read and
follow the instructions on the container.

Operate the engine for about 10 minutes to distribute
the treated fuel. Stop the engine, close the fuel shut-
off valve and let the engine cool. Drain fuel.

3.

Remove the spark plug and pour about one
tablespoon of clean engine oil into the cylinder.
Crank engine slowly to distribute oil over the
cylinder wall. Replace the spark plug.

4.

Pull the starter rope slowly until resistance is felt.
Continue pulling until the notch on the starter pulley
aligns with the hole on the recoil starter. At this
point, the intake and exhaust valves are closed.

Reel and Bedknife

1.

Wash the reel and bedknife thoroughly, then repair
and paint any damaged or exposed metal.

2.

Lubricate all fittings and friction points.

3.

Backlap the reels then back the reel away from the
bedknife. Apply a light coat of rust preventative oil to
the sharpened edges of the reel and bedknife.

After Storage

4.

Check or service air cleaner.

5.

Check oil level in the engine crankcase.

6.

Fill the fuel tank with fresh fuel. Open fuel shut-off
valve.

7.

Make certain that the tires are properly inflated.

8.

Remove all oil from the reels and bedknife. Adjust
bedknife and cutting height.

9.

Start and operate the engine at 1/2 throttle. Allow
enough time for the engine to become properly
warmed and lubricated.

CAUTION

To prevent personal injury and damage to the cutting

edges, handle the reel with extreme care.

WARNING

Never operate the engine without proper ventilation;
exhaust fumes can be fatal when inhaled.

!

!

«
...
20
21
22
23
24
...
»

Содержание tournament cut 22





















































































Отзывы:

Нет отзывов

Похожие инструкции для tournament cut 22

Бренд: Nanni Страницы: 24

Бренд: Oriental motor Страницы: 8

Бренд: Westerbeke Страницы: 64

Бренд: Raider Страницы: 193

Stagemaker SM10

Бренд: R & M Страницы: 71

Бренд: Honda Страницы: 48

Бренд: Honda Страницы: 182

Бренд: O.S. engine Страницы: 4

Бренд: O.S. engine Страницы: 28

Бренд: KRESS Страницы: 170

Xicoy AU-107K ECU

Бренд: Wren Turbines Страницы: 12

Бренд: Novy Страницы: 18

Бренд: STEYR MOTORS Страницы: 329

MINIMAX 3TNM72-GGE

Бренд: Yanmar Страницы: 2

Бренд: Hägglunds Страницы: 23

Бренд: Nanni Страницы: 93

Бренд: WÄRTSILÄ Страницы: 242

Бренд: Saito Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды