Jacobsen tournament cut 22 Скачать руководство пользователя | Manualshive

Страница: 21 / 84

background image

MAINTENANCE 7

GB-21

7.5

BACKLAPPING AND GRINDING ______________________________________________

Check for damage to the bedknife and reel blades.
Refer to (Section 6.2).

1.

Determine if backlapping or grinding will restore the
proper cutting edge.

2.

For optimum performance use a bedknife grinder to
touch-up the blade then reassemble and adjust the
bedknife to the reel as described in (Section 6.2).

3.

Assemble lapping handle or lapping machine to left
end of reel.

a.

Apply lapping compound with a long handle

brush along the entire length of the reel, (180 grit
is recommended, Section 2.6).

b.

Continue lapping and at the same time make a

fine adjustment on the reel and bedknife until
there is a uniform clearance along the full length
of the cutting edges.

4.

Carefully and thoroughly remove all lapping
compound from reel and bedknife before running
the reel in forward direction.

7.6

DAILY MAINTENANCE______________________________________________________

1.

Park the mower on a flat and level surface. Disen-
gage all drives, engage parking brake, stop the
engine and remove the spark plug wire.

2.

Grease and lubricate all points if required. To
prevent fires, wash the mower after each use.

a.

Use only fresh water for cleaning your

equipment.

Note: Use of salt water or effluent water has been
known to encourage rust and corrosion of metel parts
resulting in premature deterioration or failure.
Damage of this nature is not covered by the factory
warranty.

b.

Do not use high pressure spray.

c.

Do not spray water directly at any electrical com-

ponents.

d.

Do not spray water into the engine air intake.

Note: Do not wash a hot or running engine. Use
compressed air to clean the engine cooling fins.

3.

Fill the fuel tank at the end of each operating day.

Use clean fresh unleaded gasoline, 85 octane
minimum.

4.

Handle fuel with care - it is highly flammable. Use
an approved container, the spout must fit inside the
fuel filler neck. Avoid using cans and funnels to
transfer fuel.

a.

Never remove the fuel cap from the fuel tank, or

add fuel, when the engine is running or while the
engine is hot.

b.

Do not smoke when handling fuel. Never fill or

drain the tank indoors.

c.

Never overfill or allow the tank to become empty.

Do not spill fuel. Clean any spilled fuel
immediately.

d.

Never handle or store fuel containers near an

open flame or any device that may create sparks
and ignite the fuel or fuel vapors.

5.

Store fuel according to local, state or federal
ordinances and recommendations from your fuel
supplier.

6.

Check the engine oil at the start of each day, before
starting the engine. If the oil level is low, remove the
oil filler cap and add oil as required. Do not overfill.

«
...
19
20
21
22
23
...
»

Содержание tournament cut 22





















































































Отзывы:

Нет отзывов

Похожие инструкции для tournament cut 22

Parilla Norswift 60cc

Бренд: IAME Страницы: 9

Parilla Norswift 60cc

Бренд: IAME Страницы: 35

Бренд: DR Страницы: 20

Бренд: Man Страницы: 64

44 A FOUR-35C THREE

Бренд: Westerbeke Страницы: 61

Бренд: Ecofly Страницы: 20

1550 STERNDRIVE

Бренд: Mercury Racing Страницы: 75

Бренд: Yanmar Страницы: 52

EQP III 300 Series

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 6

Бренд: Toshiba Страницы: 31

EQP Global IEC Series

Бренд: Toshiba Страницы: 34

Бренд: Toshiba Страницы: 286

Бренд: Vanguard Страницы: 104

Duramax Diesel 2018

Бренд: GMC Страницы: 137

Бренд: GM-Racing Страницы: 4

Бренд: Volvo Penta Страницы: 29

Бренд: Volvo Penta Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды