Jacobsen HR800 Скачать руководство пользователя страница 95

Страница: 95 / 122

MAINTENANCE AND LUBRICATION 7

en-94

7.22 FOLDING ROPS ___________________________________________________________

A folding Roll Over Protective Structure (ROPS) is included with this mower. Inspect the ROPS weekly for loose

hardware or damage.

Inspect the seat, seat belt, ROPS mounting hardware and ROPS frame for
damage in accordance with maintenance chart. Replace all damaged parts

immediately. All replacement parts for the ROPS must be as specified in the

Parts Manual.

Check and torque all ROPS hardware in accordance with maintenance chart.

Do not operate the mower with the ROPS in the folded position.

There is no roll over protection with the ROPS in the folded position.

Folding the ROPS.

Remove the R clip (A) and ROPS pin (B) from both sides of the

ROPS.

Fold the ROPS toward the mower hood.

Assemble the ROPS pin and R clip to lock the ROPS in the folded

position.

Never

wear the seat belt with the ROPS in the folded

position.

CAUTION

Keep the ROPS hardware correctly fastened. Do not do any welding operations, Do not drill, change or bend

the ROPS. Replace damaged ROPS. Do not try to correct a damaged ROPS.

DANGER

In off road or transport mode, the seat belt must always be worn. The ROPS frame must be in the position for
operation. This instruction is given to meet:

The machinery directive, 2006/42/EC Sections 3.2.2, Seating & 3.4.3, Rollover.

Jacobsen. recommend that the owner operator of the machine complete a local risk assessment on the

machine to find any conditions that do not follow this rule.

WARNING

To prevent injury when you fold the ROPS, use caution to prevent your fingers being crushed between moving

and rigid parts of the ROPS.

Always wear the set belt with the ROPS frame in the vertical and locked position.

Never wear the seat belt with the ROPS in the folded position.

NOTICE

To prevent damage to the ROPS or the mower hood, do not operate the mower without the ROPS frame

locked in the vertical or folded position.

Содержание HR800



























































































































Результаты поиска

Содержание HR800

Отзывы:

Похожие инструкции для HR800

Бренды по названию

Популярные бренды

Jacobsen HR800, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание HR800

Отзывы:

Похожие инструкции для HR800

Бренды по названию

Популярные бренды