Jacobsen HR800 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 122

background image

6 ADJUSTMENTS

en-67

6.9

GENERAL INSTRUCTIONS FOR GRAMMER SEATS _____________________________

All The seat adjustments are to be done while the vehicle is stopped.

•

After removal of the backrest cover, hold the backrest frame in position with a support before the backrest
adjuster is operated. If you do not lock the frame in position safely, the backrest frame can move forward

suddenly and can cause injury.

•

Use approved GRAMMER parts.

•

Only GRAMMAR approved changes are to be made to the seat. During the removal and installation of the

GRAMMER driver seat, follow the instructions supplied by the vehicle manufacturer.

•

When you lift the driver seat, do not hold the covers. The covers are not a load bearing component and injury can

occur.

•

Before you remove the driver seat, disconnect all plug-in connectors between the seat and the vehicle supply

network. When you replace the plug-in connectors, make sure the connectors are tight so that dust and water
does not enter.

•

Fasten seat belts before operation.

•

Replace the seat belt after an accident.

•

After an accident with a vehicle that has seat belts installed, have the seat and seat mounting checked by

the safety

personnel.

•

Check the seat fasteners to make sure that the seat is installed correctly.

•

If the seat does not operate correctly, have the seat repaired in a GRAMMER workshop. Check the seat for
damage to the seat suspension and bellows or for an incorrect curve in the lumbar support.

•

If you do not correct problems that occur in the seat, the seat can damage your health and increase the risk of an

accident.

•

Before the vehicle is used, check the load sensor, installed in the seat, for correct operation. If the driver leaves

the seat, this sensor stops the vehicle.

•

If a problem is found, you must not drive the vehicle. – INCREASED RISK OF ACCIDENT –

•

Do not put the loads on to seats that have a load sensor. A load on the seat can cause the vehicle to move and

cause an accident. – INCREASED RISK OF ACCIDENT –

•

If you drive the vehicle and remove the weight from the seat, the vehicle will stop.

•

Do not load the bellows while there is a load on the driver seat. – RISK OF INJURY FROM BELLOWS –

•

Make sure that dirt and liquids can not get inside the drivers seat.

•

The driver seat is not waterproof.

•

Any changes or adjustment to a GRAMMER driver seat must be done in authorized workshops by approved

personnel. The changes must follow the operation instructions and must be in compliance with all national
regulations.

•

Incorrect installation and assembly hold the risk of personal injury or property damage. Your warranty will also be

invalidated.

«
...
66
67
68
69
70
...
»

Содержание HR800



























































































































Отзывы:

Нет отзывов

Похожие инструкции для HR800

Бренд: ECLOZ Страницы: 56

Бренд: Baroness Страницы: 199

Бренд: Yard Machines Страницы: 16

Бренд: Flymo Страницы: 174

Бренд: Rally Страницы: 28

Бренд: Simplicity Страницы: 54

Greens Super 55

Бренд: Ransomes Страницы: 76

Бренд: Jacobsen Страницы: 36

GRASS KEEPER 190 W

Бренд: Garland Страницы: 136

TURF TIGER STT61V-31KB-DF

Бренд: Scag Power Equipment Страницы: 78

Бренд: Wolf Garten Страницы: 46

Бренд: SIP Страницы: 189

Бренд: Jacobsen Страницы: 106

Бренд: Walker Страницы: 84

Бренд: Flymo Страницы: 10

Бренд: Lastec Страницы: 88

Бренд: Cub Cadet Страницы: 16

Бренд: Cub Cadet Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды