BATTERY POWER MODULE 10
en-49
10.5 BATTERY CHARGER _______________________________________________________
The battery charger is designed to fully charge the
battery pack. Read the instruction manual included with
the charger for proper operating procedure.
Before charging, the following should be observed:
The charging must take place in an area that is well
ventilated and capable of removing the hydrogen gas
that is generated by the charging process. A minimum of
five air exchanges per hour is recommended.
The charging connector components are in good
condition and free from dirt or debris. It is suggested to
apply white lithium grease to both terminals to prevent
corrosion.
The charger connector is fully inserted into the battery
pack receptacle.
The charger connector/cord set is protected from
damage and is located in an area to prevent injury that
may result from personnel running over or tripping over
the cord set.
Install all chargers in accordance with the manufacturers
instructions.
If the charger is operated in an outdoor location, rain
and sun protection must be provided.
Remove AC power cord from outlet before connecting or
disconnecting battery charger to battery pack.
The charging (DC) cord is equipped with a polarized
connector which fits into a matching receptacle on the
battery pack.
If the charger is not operating correctly, unplug charger
from both the AC outlet and the battery pack and check
the fuse. If a new fuse is required, order part number
4102780 from your Jacobsen Dealer. There is one
spare fuse included in the fuse holder.
AC Voltage
The charger is equipped with an input voltage selector
switch located on the rear of the charger. Determine what
input voltage is used in your area and set switch
accordingly before connecting AC power cord. This
charger can be used with the following AC input voltages:
100 - 130 V (Set voltage selector to 115 V (Position 1))
200 - 240 V (Set voltage selector to 230 V (Position 2))
NOTE: Charger will operate with either a 50 or 60 Hz
input voltage.
Make certain the AC power cord is equipped with an
appropriate plug for the area you live in. The charger is
equipped with a grounding plug, do not attempt to
defeat its functionality.
Note: The AC power cord included with the battery
charger is used with 115 V - 60 Hz (North America) input
voltage only. If you live in an area where 115 V - 60 Hz
input voltage is not used, a new AC power cord must be
purchased locally.
The battery charger should fully charge the battery pack
in approximately 5 hours with 115V AC input voltage.
Battery charging times may exceed 8 hours in areas
where 100V AC input voltage is used.
WARNING
Portable chargers should be mounted on a platform
above the ground, or in such a manner as to permit
the maximum air flow underneath and around the
charger. Serious damage to the charger, overheating
and potential for fire may result if the charger does
not have sufficient air flow.
!
WARNING
An ungrounded electrical device may become a
physical hazard that could result in an electrical shock
or electrocution
!
WA
RNING - F
or contin
ued protection
against fire
, re
place only with same
siz
e and type fuse
.
INTERA
CTER INCORPORA
TED
MODEL:
BA
TCH:
SERIAL NO:
INPUT
:
1. Connect and di
sconnect batter
y leads only when
supply cord is disco
nnected or arcing
and b
urning
ma
y result.
2. BA
TTER
Y LEAD CONNECTION
S - F
or a batter
y
installed in a
ve
hicle
, first conne
ct charger output
lead to ung
rounded batter
y post - not conn
ected to
automobile chassi
s - in accordance w
ith polar
ity
indication, and
then opposite
polar
ity lead to
chassis a
wa
y from batter
y; do not connect
to
carb
uretor or fuel
lines
. Disconnect chassis l
ead
first.
For batter
y not installed
in a v
ehicle
, ref
er to
instr
uction man
ual.
3. Do not o
ver
-charge batter
y - see instr
uction
man
ual
4. Do not smok
e,
str
ike a match, or cau
se a spar
k in
vicinity of batte
ry dur
ing charging.
5. Use only in a w
ell v
entilated area
.
This equipment e
mplo
ys par
ts, s
uch as s
witches and
rela
ys
, that tend to
pro
duce arcs and spar
ks and
theref
ore
, if used in a
gar
age
, locate in a r
oom or
enclosure pro
vided f
or the pur
pose or not less
than 18
inches from the floor
.
CA
UTION
- DO NO
T EXPOSE T
O RAIN:
replace def
ectiv
e cords or wires immediately
.
CA
UTION:
NE P
AS EXP
OSER A LA PLUIE.
AD
VER
TISSEMENT
: R
ISQ
UE DE MELANGE GAZE
AU
X
EXPLOSIF
. LIRE LA NO
TICE A
VA
NT D'UTILISER LE
CHARGEUR.
WA
RNING - RISK OF EXPLOSIVE GAS MIXTURE
115V
230V
Input Voltage Selector
Position
1
Position
2
Spare Fuse
Fuse Holder
Fuse