manualshive.com logo in svg

Jackson DynaTemp NB, Руководство по обслуживанию, Страница: 20 / 68

Поделиться
Скачать
Jackson DynaTemp NB Скачать руководство пользователя страница 20

13

07610-004-29-29-A

OPERATION

DETERGENT CONTROL

DETERGENT

CONTROL

Detergent usage and water hardness are two factors that contribute greatly to how 

efficiently this dishmachine will operate. Using detergent in the proper amount can 
become a source of substantial savings. A qualified water treatment specialist can 
determine what is needed for maximum efficiency from the detergent. 

1.  Hard water greatly affects the performance of the dishmachine, causing the 

amount of detergent required for washing to increase. If the machine is installed 
in an area with hard water, the manufacturer recommends the installation of 
water treatment equipment.

2.  Deposited solids from hard water can cause spotting that will not be removed 

with a drying agent. Treated water will reduce this occurence. 

3.  Treated water may not be suitable for use in other areas of operation and it 

may be necessary to install a water treatment unit for the water going to the 

dishmachine only. Discuss this option with a qualified water treatment specialist.

4.  Dishmachine operators should be properly trained on how much detergent is to 

be used per cycle. Meet with a water treatment specialist and detergent vendor 
to discuss a complete training program for operators. 

5.  DynaTemp dishmachines require that chemicals be provided for proper operation 

and sanitization and require the installation of third-party chemical feeders to 
introduce these chemicals to the machine. Contact a chemical supplier with any 
questions.

6.  Water temperature is an important factor in ensuring that the dishmachine 

functions properly, and the machine's data plate details what the minimum 

temperatures must be for the incoming water supply, the wash tank, and the 
rinse tank. If minimum requirements are not met, there is a possibility that dishes 
will not be clean or sanitized. 

7.  Instruct dishmachine operators to observe the required temperatures and to 

report when they fall below the minimum allowed. A loss of temperature can 
indicate a larger problem.

i

Содержание DynaTemp NB





































































Отзывы:

Нет отзывов