manualshive.com logo in svg

Jackson Delta HT-E-SEER-S, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Jackson Delta HT-E-SEER-S Скачать руководство пользователя страница 26

19

07610-004-54-86-D

DELIMING

OPERATION

In order to maintain the machine at its optimum performance level, lime and 
corrosion deposits must be removed. The frequency for deliming will be based on 
water conditions. A deliming solution is available from your chemical supplier. Read 
and follow all instructions on the label.

To delime machine:

1.  Remove the rinse arms and place in sink with deliming solution (leave for the 

amount of time recommended by the chemical supplier).

2.  Replace the rinse arms.

3. 

If machine is full of water, close door, press the Power button, and allow 

machine to drain and shut-off.  

4. 

Follow the Filling the Wash Tub section of this manual.

5.  Open the door and add the amount of deliming solution recommended by the 

chemical supplier.

6.  Close the door and press the Delime button on the display.  The status will 

display "DELIME."

7.  Press the Start button.

8. 

The machine will delime, drain, and refill.

9. 

Wait five minutes, then inspect the machine. If the machine is not delimed, 

run again.

10. 

When clean, press the Delime button.  The status will display "READY."

11.  Run the machine through two regular cycles to remove residual deliming 

solution.

12. The machine is now ready for normal operation.

DELIMING 

If the machine is equipped 

with an SPS and lime is 

becoming a frequent 

problem, the cartridge 

needs to be replaced. 

To order a replacement 

cartridge, see the Scale 

Prevention System page.

1 5 5

 

F

D E L I M E
O N

Содержание Delta HT-E-SEER-S































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды