background image

9

ADJUSTABLE SEAT

Never attempt to adjust the seat while the vehicle is moving. This could result In loss of control.

Adjusting Seat Forward and Rearward (If installed)(Driver's side only)

To move the seat toward the front or rear, pull the lock release lever upwards.

This releases the seat on its track so you can move it forward or rearward to

the desired position. When you find the position you want, release the lever

and slide the seat forward or rearward on its track until it locks into position

and cannot be moved further.

Seat Cushion Height Fixing (Driver's side only) (If installed)

To fix the height of the seat cushion, fit the locking knob to the locker. It will

hold your seat position from the vibration.

The other doesn't operate after the ignition key is turned to 'ACC' or "LOCK

WARNING

Be careful that someone's head, hands and body are not trapped by closing

window.

Never try to operate the main switch on the driver's door and the passen

ger's door window switch in opposing directions at the same time. If this done,

the window will stop and cannot be opened or closed.

Do not leave children alone in the car. Always remove the ignition key for

their safety.

STEERING WHEEL TILT LEVER (If installed)

To adjust the steering wheel:

1. Pull the lever upward to unlock

2. Raise or lower the steering wheel to the desired position.

3. After adjustment, securely tighten the lever by pushing it downward.

WARNING:

Do not attempt to adjust the steering wheel while driving as this may result in

loss of control of the vehicle and result in death or serious injury.

8

OWNER

S MANUAL

JAC HEAVY DUTY TRUCK

Содержание HFC4180KR1K3

















































































































Отзывы: