background image

1. POWER ON/OFF BUTTON

The radio unit may be operated when the ignition key is in the "ACC' or "ON' position.

2. VOLUME CONTROL BUTTON

Depress the "+"button to increase the volume, and depress the "

"button to increase the volume.

3. BALANCE CONTROL

Press to pop the knob out and turn it clockwise or counterclockwise until sound from the left and right speakers is about

equal from your listening position.

4. BASS/TREBLE CONTROL

Press to pop the knob out and turn to the left or right for the desired bass tone.

5. TUNE (Manual) SELECTION

When the upper side of the knob is pressed, the frequency will increase in 0.1 MHZ steps in FM band, 9 KHZ in AM

band and vice versa. With the button held down for 0.5 Sec. or more, the stop signal (broadcasting radio wave) is ig

nored, and channel selection continues.

6. CLOCK BUTTON

Depress the "CLOCK" button, the digital window will display the time.

Keep depressing the "CLOCK" button for three seconds, you can adjust the time.

Then you can adjust the time by "+" "-"button.

7. BAND SELECTOR

Pressing the BAND button changes the AM, FM bands. The mode selected is displayed on LCD.

63

1. Tune select button

2. SELECT button

3. POWER button

4. Eject button

5. Tape slot

6.FF/REW/

and

/Autoreverse

7. MODE reverse

8. Station remember

9. Digital button (1

2

3)

10. Band select

11. Digital display window

12.Seek select button

13.Time display and adjust the time

CLOCK

14 Digital button(4

5

6)

1

2

3

4

5

6

7

8 9 10

11

12

13

14

Radio

62

OWNER

S MANUAL

JAC HEAVY DUTY TRUCK

Содержание HFC4180KR1K3

















































































































Отзывы: