JAC HFC4180KR1K3 Скачать руководство пользователя страница 50

Страница: 50 / 112

●

Before towing, make sure that there is no interference between coupler

parts.

●

Confirm the adherence state of limit dog and nut, operating state of sec

鄄

ondary lock.

●

Do not tighten the nut clockwise greater than primary state absolutely.

ADJUSTING BED

By rotating the lever 1, the height of the bed is controlled.

CAUTION:

Be sure not to hurt yourself.

How to adjust rolling angle

●

Adjust the rolling angle according to vehicle nd driving condition.

●

After removing the split pin, loosen the nut by turning it counterclockwise 3

or 4 times.

●

Fix the wedge to desired position

●

Insert the split pin and bend it after the nut has been tightened.

How to adjust inside diameter of jaw

●

If the inside diameter of jaw is worn, adjust it.

●

Turn the limit dog with a tool counterclockwise.

●

Loosen the nut slowly. This will diminish the inside diameter of jaw accord

鄄

ing to moving yoke forward.

●

If it's inside diameter is 51-51.2 using the Gauge, tighten the limit dog to

adhere the nut perfectly. At this time, check that the gauge could be rotated

by hand.

OWNER

’

S MANUAL

JAC HEAVY DUTY TRUCK

Содержание HFC4180KR1K3

















































































































Результаты поиска

Содержание HFC4180KR1K3

Отзывы:

Бренды по названию

Популярные бренды

JAC HFC4180KR1K3, Руководство пользователя

Результаты поиска

Содержание HFC4180KR1K3

Отзывы:

Бренды по названию

Популярные бренды