Installation manual: OASiS security system JA-82KRC
18 / 21
MKH51100_OS2
12.45. Go to maintenance mode
By entering
292
while in Service Mode the system switches to
maintenance mode. In maintenance mode it is possible to
program the devices to be bypassed and to adjust the control
panel internal clock (see 13.4).
12.46. Setting the internal clock
The control panel has a built in real-time clock which is used to
time-stamp all recorded events in the control panel memory.
Adjust the clock after installation by entering:
4 hh mm DD MM YY
where:
hh
is the time in hours (00 to 23)
mm
is the time in minutes (00 to 59)
DD
is the day (01 to 31)
MM
is the month (01 to 12)
YY
is the year (00 to 99)
Note
: The internal clock can also be adjusted in maintenance mode.
Example: On 30 June 2012 at 17:15 enter: 4 17 15 30 06 12
After the control panel is powered up, the clock is set to 00 00
01 01 00.
12.47. Editing keypad text
The names of devices and programmable outputs as displayed
on the keypad unit can be edited as follows:
•
Pressing and holding the
?
key (in service mode) enters text
editing mode and the name of the device enrolled to address
01 is then displayed with a flashing cursor on the first text
character.
•
Key
functions:
and
text scrolling (see table)
1
and
7
character-selection (A,B,C,D.......8,9,0)
4
and
5
cursor control (left/right)
2
delete selected character
#
exit editing (& save changes)
List of editable text:
text
Description
01: to 50: Devices
Names of devices in addresses 01 to 50
Control panel
Name of control panel (e.g. displayed if its cover
is opened)
Keypad
Name of hard-wired keypad
Communicator
Name of the communicator in the control panel
Master code
Name of the master code
01: to 50: Code
Names of user codes
ARC Code
Names of ARC code
Service code
Name of the service code
PGX and PGY
Names of programmable outputs
OASIS JA-82
The default text displayed in operating mode if
no other text needs to be displayed. If erased
then nothing will be displayed.
Notes:
•
Only capital letters can be entered.
•
The length of text is limited to the length of the display.
•
The text is only stored in the keypad used for editing (different
keypads in the system can show different text if desired).
•
Text is stored in the non-volatile memory of keypads, so power
disconnection will not erase any stored text.
•
Convenient text editing is possible using a PC running OLink
software.
•
Besides device names, keypads also use so-called internal text such
as “service”, “maintenance mode” etc, and this text can also be
edited via OLink software by selecting “Settings” on the menu and
then “keypad text”.
•
After editing keypad text using OLink software, all keypads (including
wireless ones) must be connected to the digital bus to save the
changes to the keypad units by clicking on the OK button in the
software.
Factory default setting: in addresses 01 to 50 there is the text
“Device”. Other default text: “Control panel”, “Keypad”,
“Communicator”, “Master code”, users 01 to 50 “Code”,”ARC
Code”, “Service code”, “PGX”, “PGY” and “OASIS JA-82”.
13. Operating the system
The Oasis system can be operated locally using a keypad or a
keyfob and it can also be operated remotely by mobile phone or
the Internet (if equipped with a suitable communicator).
13.1. The
system
keypad
Indoor keypads model JA-80F (wireless) or JA-80E (wired) can
be used to operate and program the system. Both keypad types
provide the same functionality:
13.1.1. Keypad
indicators:
ABC setting (arming) status of sections
– if all sections are
set then all these indicators (A B & C) are lit.
Flashing =
alarm,
with the simultaneous
display of alarm details on the LCD,
e.g.:
Alarm
03:
Kitchen
Constantly lit =
fault
– details are displayed by
pressing the “
?
” key
Power
. Constantly lit = mains ok. Flashing = no
mains, control panel powered by back-up battery
only.
13.1.2. LCD
display
The 1
st
line displays the status:
triggered detector, Service
mode etc. In standby mode, it shows the text “OASIS JA-80”
(editable, see 12.47).
The 2
nd
line displays the name of a device.
(e.g. 01: Main
Door etc.). The text can be edited, see 12.47.
Displaying the status of detectors and programmable
outputs:
Details on permanently triggered detectors (e.g. open
windows) and the status of the PGX and PGY outputs can be
displayed by pressing the
?
key.
13.1.3. Keypad
display
sleep-mode
In operating mode, the wireless keypad unit displays the
system status for 20 seconds (if battery-powered) after the last
interaction with a user, and then goes into sleep mode. Pressing
any key, triggering the keypad input or opening the keypad’s flip
cover re-activates the display.
13.1.4. Keys
0–9
digital code entry
∗
function sequences
#
escape
