Alarm system JA-60 “COMFORT”
-
10 -
MDY51306
7.2. Control panel programming
Enter
F 0 SC
(SC = Service Code, factory default SC=6060) to enter the programming mode (indicated by a „P“ on the
LED display). This can only be done while the panel is disarmed. In this mode no alarm can be triggered. Detectors and
other accessories can be enrolled, the control panel and telephone dialer parameters can be set up and the system can
be tested.
By entering programming sequences from the keypad (see bellow) the parameters of the control panel can be set. The
control panel checks the validity of the entered sequences, and any incorrect code is refused (sequence will be termi-
nated). Any unfinished programming sequence can be terminated by pressing the
N
key.
To exit the programming mode, press the N
key („P“ will turn off). If any fault is indicated when you try to exit the pro-
gramming mode, the control panel will inform you about the problem (see programming sequence 39x for more details).
*
Setting of these parameters in following sequences is available only for a control panel with a built in optional dialer
7.2.1. Testing of the system when the LED display displays „P“
In the programming mode (indicated by a „P“) no alarm can be triggered. The control panel will confirm receiving any sig-
nal from an enrolled detector or another JA-60 wireless item. It will make a beep (press F to select the loudness of the
beep) and the LED display will show which signal was received. Some detectors (JA60P, JA60M etc.) have an extra test-
ing mode, which is usually activated for 5 minutes after the detector’s cover is attached (see manuals of the particular
detectors).
Just as in the programming mode, the signals from all enrolled items are confirmed in the user mode (confirmed by a
“U”). The user mode is accessible with the Master code and the supervisor of the system can use this mode to replace
batteries in items or for system testing. To open the user mode enter F 0 MC (= Master Code) when the control panel is
disarmed.
7.2.2. Enrollment (teaching) of wireless items enter:
1
As a maximum 16 detectors and 8 controllers (remote controls & keypads) can be enrolled to the control panel. A wireless
siren and an additional JA60K control panel (subsystem) can be enrolled as well.
•
press key
1
(while „P“ is displayed) to enter the enrolling mode. The control panel will display the next free position to
enroll a detector.
•
Use key 1 and 6 to scroll
(up and down) all control panel positions – 1 to 16 (detectors) – c1 to c8 (controllers & key-
pads) – A (wireless siren) – J (sub control panel JA-60). The display shows the position number while the Battery LED
indicates if the position is occupied (If the Battery LED is illuminated, it indicates that position is occupied).
•
Detectors and keypads are automatically enrolled when their power is switched on (batteries are installed). A remote
control is enrolled only after both of its buttons are simultaneously pressed and held for 3 seconds. A subsystem con-
trol panel will enroll after sequence 299 in entered while it is in its programming mode. The system will not allow en-
rollment of an item into a non-corresponding position (a detector can not be enrolled into a controller position etc.). If
you try to enroll any item into a wrong position, the control panel will automatically select a suitable position.
•
Control panel confirms enrollment
with a „beep“ (press F to select a louder “beep” sound). The LED display will
show the number of the enrolled item for 2 seconds and then it will display the number of the next free position.
•
To change the position
of an enrolled item is simple.
Enroll it to the new selected position
(the item will „move“). If
you enroll an item to an occupied position, the former item will be deleted and only the new enrollment is valid. Only
one item (detector, controller etc.) can be stored to each position.
•
Erase an enrolled item
the following way: in the enrolling mode select the corresponding position and then press and
hold key 2 for two seconds. The item will be erased (confirmed with a long beep). If you press and hold key 3, all en-
rolled controllers (remote controls and keypads) will be erased. Pressing and holding key 4 will erase all enrolled items
(detectors, controllers, siren and the sub system).
•
Wireless siren will generate enrollment signal
when its power is switched on (it will enroll to position A). If you need
to enroll a siren which is already powered and it is not possible to easily switch its power off, you can enroll it the fol-
lowing way: enter the enrolling mode and then enter the 6 digit siren production code (printed in the siren’s manual).
The control panel will “request” the siren to send its enrollment signal. The siren will send the signal only if it has no
current communication with any other control panel (This protects you from enrolling your neighbor’s siren). Enrollment
takes about five seconds after the code is entered.
Note: if an item was not enrolled after its batteries were installed, it is because the control panel recognized its radio signal
as a poor one. Items are only enrolled if their radio signal has a level which guarantees reliable communication. Check the
detector’s batteries and try to enroll the problematic sensor once more. If it is not accepted by the control panel, you
should change the location of the item. All items should be located 1 m or more from the control panel.
