Jabiru 2200 Скачать руководство пользователя | Manualshive

Страница: 68 / 201

background image

Engine Overhaul Manual

Jabiru Aircraft

Pty Ltd

Jabiru 2200 & 3300 Aircraft Engines

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

1

2

3

4

5

6 7

Dated : 28/10/2014

Issued By: AS

Page: 68 of 201

L:\files\Manuals_For_Products\Engine_Manuals\Overhaul_Manual\JEM0001-7_Overhaul_Manual_DRAFT_(29_10_14).docx

– Hydraulic lifter engine camshafts have 2 dots on the flange and 2 rings around the front of the

camshaft to indicate a hydraulic lifter camshaft. The photos above show a hydraulic lifter (260°
duration, non-roller) camshaft.

– If the camshaft in your hydraulic engine has a single ring around the front (285° duration) it must

be replaced with a current 2 ring camshaft and new lifters to suit at overhaul.

– Engines equipped with roller followers use a different cam which is not marked with ID rings. This

part can be easily identified by the more rounded shape of the cam lobes (Figure 77)

Figure 76

– 2-Ring Camshaft

Figure 77

– Roller Cam Lobe

5.10.3.2 Cleaning



Clean out the 4 threaded holes in the rear flange with a 1/4” UNF tap.



Clean the camshaft with kerosene and dry.



Coat with engine oil or other corrosion preventative.

5.10.3.3 Inspection



Visually inspect the lobes for any abnormal wear patterns and any chipping around the sides of the

lobes. Any chipping or signs of wear through the hardened surface will require a new camshaft. Inspect
the lifters for signs of wear on the face. If replacing the camshaft the lifters must also be replaced.



The camshaft and the camshaft drive gears must now be inspected for structural integrity with MPI

(Magnetic Particle Inspection).



The overhauler must be aware that of the different types and combinations of camshafts and lifters

fitted to Jabiru engines over the years currently only three combinations are approved: a solid lifter
(zero ring) cam with solid lifters, a hydraulic lifter (260° duration, 2-ring) cam for hydraulic lifters and a
roller follower cam (rounded lobes) for roller follower engines. Engines with other configurations must
be updated to an approved configuration at overhaul.

Note large tip radius
for roller cam

«
...
66
67
68
69
70
...
»

Содержание 2200










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2200

Бренд: FAZUA Страницы: 76

Бренд: Kubota Страницы: 138

AstroTrack 21047

Бренд: ORION TELESCOPES & BINOCULARS Страницы: 2

Бренд: Deutz Страницы: 37

Бренд: SOMFY Страницы: 48

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 38

Бренд: Lister Petter Страницы: 24

Бренд: GSK Страницы: 24

Бренд: Honda Страницы: 2

Бренд: Motion Страницы: 52

Бренд: Bosch Rexroth Страницы: 56

ZT-5400 Powertrain

Бренд: Hydro-Gear Страницы: 48

Бренд: JAC Страницы: 14

Бренд: HSD Страницы: 72

Diesel Engines S16R-Y2PTAW-1

Бренд: Mitsubishi Страницы: 3

Бренд: Vetus Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды