background image

11

Machine Operating Instructions: 

1) Read safety instructions on previous pages.
2) Insert coins (or bills) to start.
4) Using increase or decrease buttons select desired pressure.
5) Apply chuck to tire valve stem and fill to desired pressure.  NOTE: For best results, remove valve stem covers on all 

tires before depositing money.

6) Hang hose up when finished.

How Does Digital Air Work?

When the compressor is running, the machine will dispense air out the chuck.  When air dispensing stops, the 
system is searching for back pressure from the tire.  Once back pressure is sensed, the machine will continue to 
dispense air out the chuck until the tire is filled to the programmed pressure. If the digital air machine cannot fill a 
low tire, the tire probably needs serviced.

Maintenance:

All servicing of machine should be conducted by an authorized service representative!

Periodically inspect hose, chuck, and chuck washer for wear or fatigue.

Every month remove filter from compressor and clean.

Periodically inspect electrical wires and connections for wear or fatigue.

Clean canister with a stainless steel cleaner as needed.  

Decals can be cleaned with mild soap and water.

Replacement parts can be ordered through JE Adams or your nearest dealer.

REV 3-23-22

Содержание 8670 Seies




















Отзывы: