background image

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

J/145 OWNER GUIDE  

 

7

Commissioning Checklist

Pre-Launch 

___ Read equipment owner manuals 

___ Pre-rig mast and check installation of: 

 halyards 

 blocks 

 electronics 

 shrouds 

 

spreader chafe guards 

 lifeline 

pins 

___ Pre-rig boom 

___ Bottom painted or touched up 

___ Check propeller/strut/zinc 

___ De-winterize engine and check status of: 

 

engine oil/ filter 

 coolant 

level 

 

transmission fluid level 

 water 

intakes/filter 

 

fuel lines/filter

 

___ Check battery charge 

___ Align prop vertically & mark shaft 

___ Check all hose clamps, tighten as required 

___ Close all seacocks 

Loose Gear 

___ Fenders and lines 

___ Dock lines 

___ Winch handles 

___ Ignition keys 

___ Bilge pump handles 

___ Mast wedges/Spartite lubed 

___ Double-check sling locations and mark 

Launch  

___ Check for leaks 

___ Check seacocks 

___ Check shaft seal for leaks 

 

 

Engine Start 

___ Read engine owner’s manual 

___ Align engine and shaft 

___ Start engine 

___ Check exhaust for cooling water flow 

___ Check oil press., water temp., charging gauges 

___ Check transmission- forward/reverse 

___ Check shaft seal 

Step  Mast 

___ Remove interior headliner at mast opening 

___ Hoist spar and lower into boat 

___ Attach furler to stemhead fitting 

___ Attach hydraulic cylinder to backstay and plate 

___ Attach all shrouds and hand tighten 

___ Install wedges/Spartite and mast boot  

___ Connect mast junction box wires 

Rigging 

___ Install boom 

___ Lead all halyards to stoppers on cabin top 

___ Rig reef lines 

___ Install and connect  boom vang 

___ Rough tune spar per tuning guide 

Systems Check 

___ Fill water tanks- flush twice to eliminate anti-freeze 

___ Check water pressure system, bleed air if necessary 

___ Fill and check LPG system 

___ Fill fuel tanks 

___ Check operation of electrical systems and pumps 

___ Check sailing electronics  

Trial Sail 

___ Raise and lower sails to check for fit 

___ Monitor engine performance and check shaft seal 

___ Check bilge for leaks 

___ Check sailing electronics 

___ After sailing, re-caulk main chainplates 

___ Mark locations in cockpit to install teak foot braces 

(shipped loose) 

Содержание J/145




















































Отзывы: