background image

7

/7

System Operation Manual - IZIP E3 Metro

12/23/13

“F” Illuminates 

when the battery is 

nearly full.

The cell diagram 

indicates the charge 

level of the main 

battery.

“E” Illuminates 

when battery is 

nearly empty.

The down arrow 

Illuminates while 

braking.

The up arrow 

Illuminates while the 

motor is being powered.

Understanding the battery gauge

The gauge should show the battery level within a 

few moments of turning on. Each “bar” represents 

20% of the battery’s full charge.

If the gauge still shows completely empty after a 

few seconds, check all connections to the control-

ler and display, and re-connect. 

You may also need to begin riding the bike before 

the battery “wakes up” fully and begins sending 

the charge signal to the display.

Comm Error

Interpreting error messages

The IZIP display shows 

coded error messages to 

help diagnose problems 

with the bike. These 

messages appear 

automatically if the system 

senses an issue.

The most common error 

message you may see 

is Error 13: “Comm Error”. If this error comes up, it 

means that the display is connected to the bike but 

cannot communicate with the main controller (located 

in the bike’s downtube).

Make sure the bike’s battery is installed and fully 

charged. Check all connections between the display 

and the controller, the battery and the controller, and 

the display and its mounting bracket. Re-mount the 

display, making sure it engages the mount fully.

If problems persist, or for information on other error 

codes, please contact Currie Tech customer service.

Changing the display battery

The display can use power either from its 

internal battery, or from the bike’s main 

battery. The internal battery is used when the 

display is disconnected from the bike, so you 

can browse your ride data (like distance, time, 

and average speed). 

The display is powered by the bike’s battery 

when connected to the bike. Even if the 

internal battery in the display is dead or not 

installed, the display will still operate using main battery power. However, if 

you disconnect the display from the bike, it will immediately shut off.

The display uses one CR2032 3V watch battery. It should be available at 

any store that sells electronics.

To replace, unscrew the display’s back cover using a coin. Remove the old 

battery, then replace with a new one, oriented as shown (you should be 

able to see the + symbol on the top of the cell). Replace the back cover, 

tightening about 3/4 turn until snug. 

After replacing the battery, you will need to re-set the clock. Trip time, trip 

distance, average speed, and max speed will also be reset. The odometer 

and total time values are stored in memory and will not be reset.

Содержание E3 Metro








Отзывы: