iWave iW-RainboW-G21M Скачать руководство пользователя страница 24

Страница: 24 / 92

REL1.1

Page 24 of 92

RZ/G1H Qseven SOM Hardware User Guide

iWave Systems Technologies Pvt. Ltd.

2.6.11

DATA UART Interface

The RZ/G1H Qseven SOM supports two UART interface on Qseven Edge connector for Data UART interface and Debug

UART interface. RZ/G1H

CPU’s SCIF

B2 controller is used for Data UART interface with hardware flow control for request

to send and clear to send signals on Qseven Edge connector.

The RZ/G1H

CPU’s SCIFB

2 supports serial communication interface incorporating 256-byte transmit/receive FIFOs that

handles asynchronous communication. Serial data communications can be carried out with standard asynchronous

communications chips such as a Universal Asynchronous Receiver/Transmitter. It has On-chip baud rate generator

that allows any bit rate to be selected. Also it supports multi-byte DMA transfers.

For more details, refer Qseven Edge connector pins 171, 172, 177 & 178 for Data UART interface on

Table 4.

2.6.12

CAN Interface

The RZ/G1H Qseven SOM supports one CAN interface on Qseven Edge connector along with one more CAN interface

on Expansion connector2. RZ/G1H

CPU’s

CAN module supports two channels in which CAN1 channel is connected to

Qseven Edge connector.

The RZ/G1H

CPU’s

CAN module complies with the ISO11898-1 Specifications and supports programmable bit rate up

to 1 Mbps with both formats of messages namely the standard identifier (11 bits) and extended ID (29 bits). It also

supports 64 mailboxes in two selectable (Normal and FIFO) mailbox mode. To connect external CAN module to this

bus, it is necessary to add transceiver in between.

For more details, refer Qseven Edge connector pins 129 & 130 on

Table 4.

2.6.13

SPI Interface

The RZ/G1H Qseven SOM supports one SPI interface with two chip selects on Qseven Edge connector along with one

more SPI interface on Expansion conenctor2. RZ/G1H

CPU’s

MSIOF0 is used for SPI interface which supports full-duplex

synchronous four-wire serial interface with DMA.

The RZ/G1H

CPU’s

MSIOF0 supports serial formats IIS, SPI (master and slave modes) at max speed of 26Mbps. It

supports 32bit x 64 stages for transmit FIFOs & 32bit × 256 stages for receive FIFOs and allows MSB first or LSB first

selectable for data transmission and reception.

For more details, refer Qseven Edge connector pins 199 to 203 on

Table 4.

Содержание iW-RainboW-G21M





























































































Результаты поиска

Содержание iW-RainboW-G21M

Отзывы:

Бренды по названию

Популярные бренды

iWave iW-RainboW-G21M, Руководство пользователя по оборудованию

Результаты поиска

Содержание iW-RainboW-G21M

Отзывы:

Бренды по названию

Популярные бренды