iWave iW-RainboW-G20M Скачать руководство пользователя страница 21

Страница: 21 / 80

REL1.3

Page 21 of 80

RZ/G1M/G1N Qseven SOM Hardware User Guide

iWave Systems Technologies Pvt. Ltd.

2.6.8

LVDS Display Interface

The RZ/G1M/G1N

CPU’s

display unit (DU) has two independently controllable channels DU0 & DU1 and supports LVDS

interface and RGB888 interface. In RZ/G1M/G1N CPU, LVDS interface is dedicatedly connected from DU0 and RGB888

interface can be connected either from DU0 or DU1. Using the DU0 and DU1, different images or the same image can

be displayed on two displays.

The RZ/G1M/G1N Qseven SOM supports one LVDS interface on Qseven Edge connector and one RGB888 interface on

Expansion connector1. The RZ/G1M/G1N

CPU’s

LVDS module converts an RGB signal output by the DU0 module to

the LVDS format. This LVDS output supports five differential output pairs (4 data and 1 clock) that conform to the

TIA/EIA-644 standard with dot clock operating frequency of 31MHz to 148.5 MHz. The LVDS interface supports 8

output data formats which can be selected by register settings.

The RZ/G1M/G1N

CPU’s

LVDS output is directly connected to primary LVDS channel of Qseven Edge connector. LVDS

panel power enable and LVDS panel backlight enable output are supported on Qseven Edge connector from

RZ/G1M/G1N CPU GPIOs GP7_25 and GP5_14 correspondingly. Also LVDS panel backlight brightness control output is

supported on Qseven Edge connector from RZ/G1M/G1N

CPU’s

PWM output (PWM3/TPU3).

For more details, refer Qseven Edge connector pins 99, 101, 103, 105, 107, 109, 111, 112, 113, 115, 119, 121 & 123

Table 4.

2.6.9

I2S Audio Interface

The RZ/G1M/G1N Qseven SOM supports one I2S audio interface port on Qseven Edge connector. RZ/G1M/G1N

CPU’s

SSI0 & SSI1 of SSIU is used for I2S interface. Also RZ/G1M/G1N Qseven SOM supports reset output on Qseven Edge

connector for carrier board Audio Codec from RZ/G1M/G1N CPU GPIO (GP2_13).

The RZ/G1M/G1N

CPU’s

serial sound interface (SSI) is a transceiver module designed to send or receive audio data

interfacing with a variety of devices offering I2S format. It also supports master/slave functions and multi-channel

format functions. The frequency range of SCK signal is from 297.3 kHz to 12.5MHz at master mode and from 297.3 kHz

to 15.1 MHz at slave mode. SSI Module supports TDM format operation at 44.1 or 48-kHz sampling rate.

For more details, refer Qseven Edge connector pins 59, 61, 63, 65 & 67 on

Table 4.

Содержание iW-RainboW-G20M

















































































Результаты поиска

Содержание iW-RainboW-G20M

Отзывы:

Похожие инструкции для iW-RainboW-G20M

Бренды по названию

Популярные бренды

iWave iW-RainboW-G20M, Руководство пользователя по оборудованию

Результаты поиска

Содержание iW-RainboW-G20M

Отзывы:

Похожие инструкции для iW-RainboW-G20M

Бренды по названию

Популярные бренды