background image

- 2 -

Safety Instructions

CAUTION

CAUTION

Prohibited

● 

Do not place the pump close to water.

 The pump is not dust-/water-proof construc-

tion. The use of the pump in a humid place 

or a place where the pump can get wet may 

result in an electrical shock or short-circuit.

● 

 

Do not run pump dry.

If the pump runs without a liquid, the pump 

is damaged by friction heat.

● Do not damage a power cable.

 Risk of fire or electrical shock. Do not 

scratch, modify, or pull a power cable. The 

cable can also be damaged when it is heat-

ed or loaded with a heavy thing.

● 

 

Earthing

Risk of electrical shock. Always earth the pump.

 

 

Do not pressurize the pump over the 

maximum discharge pressure.

A leak may result from the sealing surface 

of O ring, or the pump fails at worst.

 

 

Install an earth leakage breaker.

An electrical failure of the pump may ad-

versely affect related devices. Purchase and 

install an earth leakage breaker separately.

● Power cable is not replaceable.

 Do not use any damaged power cable for 

the prevention of a fire or electrical shock. 

The cable is not replaceable, so that the 

whole pump unit needs to be replaced when 

the cable is damaged.

● Limited operating site and storage

 Do not install or store the pump:

1.  Where ambient temperature can exceed 

40°C or falls below 0°C.

2.  Under a flammable/corrosive atmosphere.

3. Under direct sunlight or rainwater

 

 

Disposal of the used pump

Dispose of any used or damaged pump 

in accordance with relevant regulations. 

Consult a licensed industrial waste products 

disposing company.

● 

Static electricity

 When low electric conductivity liquids such 

as ultra-pure water and fluor inactive liquid 

(e.g. Fluorinert

TM

) are handled, static elec-

tricity may generate in the pump and may 

cause static discharge. Take countermeas-

ures to remove static electricity.

● 

Fasten the front casing tight

Liquid may leak if front casing fixing screws 

are loose. Tighten the screws before initial 

operation or at intervals.

Caution

Prohibited

Electrical shock

Earthing

Caution

Prohibited

Electrical shock

Prohibited

Содержание MD-100F

























Отзывы: