IVIE MPS 2300 Скачать руководство пользователя страница 8

Страница: 8 / 48

lvie Technologies

MPS 2300

Basic
Instructions

Check for carton damage while unpacking.

Unpacking and

Inspection.

Check the product for loose or rattling parts.

Save the carton for return shipment, if required.

If shipping damage is evident,

notify the transpor-

tation company immediately. File a claim with the carrier
for shipping damage. Be sure to save the carton for the
Shipper to inspect.

Keep power OFF when making any connections.

Important

Installation
Precautions.

Check the AC voltage before connecting the AC

plug.

CONNECTION TO WRONG VOLTAGE WILL IM-

MEDIATELY DAMAGE THE PRODUCT, and voids the

warranty.

Start with the Master Volume controls all the

way

off. Turn the controls up gradually until normal

operation is verified.

Never connect speaker barriers from different

channels together or the same speaker to more
than one channel.

Do not connect speaker barriers to chassis or

signal ground.

Keep speaker wiring separate from input wiring.

Always connect speakers with power off. Use

heavy gauge cable with no frayed strands or
damaged insulation.

Failure to observe precautions could lead to fire

or shock hazard.

Never plug in a damaged amplifier

until the condition of the internal insulation is checked. If

the internal fuse blows the amplifier section is defective

and must be repaired or replaced.

Be sure to provide adequate support and

ventilation.

Содержание MPS 2300

















































Результаты поиска

Содержание MPS 2300

Отзывы:

Похожие инструкции для MPS 2300

Бренды по названию

Популярные бренды

IVIE MPS 2300, Руководство пользователя

Результаты поиска

Содержание MPS 2300

Отзывы:

Похожие инструкции для MPS 2300

Бренды по названию

Популярные бренды