ITW SIMCO ION 4000074 Скачать руководство пользователя страница 3

Страница: 3 / 28

R50 Blue Bar

5101171 Rev. L

1. SAFETY WARNINGS

NOTE!

– Statements identified with a

NOTE

indicate precautions necessary to avoid

potential equipment failure.

CAUTION!

– Statements identified with a

CAUTION

indicate minor or moderate

injury is possible.

WARNING!

– Statements identified with a

WARNING

indicate serious injury is

possible.

NOTE!

– This equipment must be correctly installed and maintained. Adhere

to the following notes for safe installation and operation.

1.   Read instruction manual before operating or installing device.
2.   Qualified service personnel must do installation and repairs.
3.   Ground the frame of the machine on which the power supply and neutralizing bars

are mounted.

4. Disconnect supply voltage to power supply before connecting neutralizing bar to the

high voltage terminal strip.

CAUTION!

–

Electrical Shock Hazard

1. Do not touch bar when power supply is energized.
2. Disconnect supply voltage to power supply before connecting bar or

performing any maintenance to the system.

WARNING! – Fire Hazard

Do not install or operate equipment in close proximity to any flammable

solvents or flammable materials.

Содержание SIMCO ION 4000074





























Результаты поиска

Содержание SIMCO ION 4000074

Отзывы:

Похожие инструкции для SIMCO ION 4000074

Бренды по названию

Популярные бренды

ITW SIMCO ION 4000074, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SIMCO ION 4000074

Отзывы:

Похожие инструкции для SIMCO ION 4000074

Бренды по названию

Популярные бренды