ITW SIMCO ION 4000074 Скачать руководство пользователя страница 25

Страница: 25 / 28

R50 Blue Bar

5101171 Rev. L

7. MAINTENANCE

It is recommended that maintenance of R50 Blue Bars be performed every three weeks.

Dirty environments may require more frequent cleaning. Maintenance to power supply

should be performed every month.

WARNING –

Maintenance must be performed by qualified service personnel.

R50 Blue Bar

A cleaning brush with nylon bristles should be used to keep the ionizing pins of the bar

clean. Periodic use of the brush will prevent deposits from accumulating on the pins. The

ionizing pins must remain sharp for optimum operation.

NOTE

– DO NOT SCRAPE PINS WITH ANY HARD OR SHARP

OBJECT THAT MAY DAMAGE THE POINTS.

WARNING – Fire Hazard

Do not turn on power supply until all traces of alcohol or mineral spirits are

removed.

CAUTION

–

Electrical Shock Hazard

Turn off power supply before cleaning static bar.

1. Remove dirt particles deposited on the Blue Bar with the cleaning brush or dry

compressed air.

2. Remove resistant coatings deposited on the bar by wiping with isopropyl alcohol or

mineral spirits applied to a clean cloth.

3. Do not soak bar or related components in alcohol or mineral spirits. Do not use

harsh solvents such as lacquer thinner, naphtha or acetone as they will damage the

bar housing and epoxy.

Wipe the Blue Bar and supports with a clean dry cloth. Do not apply power to bar until

all traces of alcohol or mineral spirits have been removed.

Functionality Check of “N” Power Supplies

The power supply does not require any special maintenance. The use may occasionally

check to make certain all ground and electrical connections are clean and tight.

Содержание SIMCO ION 4000074





























Результаты поиска

Содержание SIMCO ION 4000074

Отзывы:

Похожие инструкции для SIMCO ION 4000074

Бренды по названию

Популярные бренды

ITW SIMCO ION 4000074, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SIMCO ION 4000074

Отзывы:

Похожие инструкции для SIMCO ION 4000074

Бренды по названию

Популярные бренды