ITW 4016874 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 28

background image

3

IQ POWER MPS POWER SUPPLY

5201279 Rev A

Features

• The IQ Power LP static neutralizing bar features a low profile.
• Static bar disconnect plug pre-installed on static bar cable for quick and

easy installation.

• Ionization emitter points current limited to enhance operator safety.
• Ionization emitter points of tungsten to extend operating life of emitter

points.

• Continuous mounting slot on static bar and mounting brackets for easy and

flexible installation.

• Indicators on power supply display status of neutralizing system and

detection of system faults.

• Connection available on power supply for remote sensing, alarm status and

standby control of power supply.

• Optional control station that provides power and a communication hub for

IQ Power static neutralizing systems.

• Optional static sensor bar for gathering web charge data (used in CLFB

mode).

«
...
3
4
5
6
7
...
»

Содержание 4016874





























Отзывы:

Нет отзывов

Похожие инструкции для 4016874

Бренд: Vacon Страницы: 6

Бренд: E-Lite Страницы: 4

VisionXS-IP-C-DP-UHR

Бренд: G&D Страницы: 144

Бренд: JAMEC PEM Страницы: 4

BT-CK 18 2B-1.5 Kit

Бренд: Taurus Страницы: 40

Бренд: Stihl Страницы: 20

Бренд: Tryton Страницы: 48

HEAT GUN HG 1500

Бренд: Earlex Страницы: 6

Бренд: Wel-Bilt Страницы: 4

Бренд: Shop fox Страницы: 64

Бренд: Parkside Страницы: 2

Бренд: easydriver Страницы: 13

Бренд: HuntKey Страницы: 4

Бренд: YOKOGAWA Страницы: 2

GRG402 Giant II

Бренд: Band-it Страницы: 3

Бренд: Resi Страницы: 60

Бренд: Hilti Страницы: 2

Бренд: YATO Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды