ITV ICE MAKERS ALFA Скачать руководство пользователя

Страница: 24 / 27

NG DP

TECHNICAL SERVICE MANUAL

8.6. Spray nozzles and connecting pipes

1) Remove the curtain (it can be cleaned with vinegar or phosphoric acid, rinse, clean with lye,

rinse

)

2) Remove the metal grill and clean likewise.

3) PULL UPWARDS THE CONNECTING PIPE. IT HAS BEEN ASSEMBLED BY PRESSING

IT INTO PLACE.

4) Disassemble the nozzles and the connecting tube covers and clean them.

5) Disassemble and clean the main filter of the production unit. (IT IS ASSEMBLED BY

PRESSING IT INTO PLACE)

6) Assemble the filter, nozzles and connecting tube.

ATTENTION:

ESSENTIAL

THAT

SPRAY

NOZZLES

ARE

COMPLETELY

PERPENDICULAR TO THE CONNECTING TUBES, OTHERWISE THE CUBES AT THE

ENDS MAY NOT RECEIVE WATER.

7) Place the grill over the nozzles, with the back slots secure.

8) Install the curtain, ensuring that all of the strips can move freely.

9) Run the machine but DISCARD THE FIRST SET OF ICE CUBES

8.7. Cleaning the water inlet filters

These round wire gasket filters placed on either end of the water hose to mains, often become

blocked in the first few days of use, Especially When The Plumbing Installation Is New. Clean

them under a jet of water.

8.8. Checking for water leaks

This must be done whenever maintenance is carried out on the machine: check all water

connections, braces, tubes and hoses in order to eliminate leaks and prevent breakages and

flooding.

Содержание ALFA




























Результаты поиска

Содержание ALFA

Отзывы:

Похожие инструкции для ALFA

Бренды по названию

Популярные бренды

ITV ICE MAKERS ALFA, Техническое и сервисное руководство

Результаты поиска

Содержание ALFA

Отзывы:

Похожие инструкции для ALFA

Бренды по названию

Популярные бренды