ITV ICE MAKERS ALFA Скачать руководство пользователя

Страница: 3 / 27

NG DP

TECHNICAL SERVICE MANUAL

1. INTRODUCTION

Thank you for choosing

ITV

NG DP

Ice Cube Maker.

You have purchased one of the most reliable ice-making products on the market today.

Carefully read the instructions contained in this manual since they provide important information

relative to safety during installation, use, and maintenance.

1.1. Warnings

This appliance should be installed by approved Technical Service Personnel.

This plug should be accessible at all times.

To reduce the risk of electrical shock, ALWAYS disconnect the machine BEFORE cleaning or

maintaining the equipment. Do not attempt to install, service, or modify this machine. Improper

use by other than specially trained technicians is extremely dangerous and may result in a fire

or electric shock.

This machine should not be placed outdoors or exposed to rain.

Connect to drinking water mains.

This appliance is not intended for use by young children or infirm persons without supervision.

Young children should be supervised to ensure that they do not play with the appliance.

IMPORTANT!

•

DO NOT ATTEMPT TO SERVICE THIS MACHINE AS IT IS DANGEROUS AND COULD

CAUSE SEVERE DAMAGE TO THE UNIT.

•SERVICE SHOULD ONLY BE CARRIED OUT BY TRAINED, QUALIFIED PERSONNEL.

•WE STRONGLY RECOMMEND USING ONLY ORIGINAL REPLACEMENT PARTS

AVAILABLE FROM AN AUTHORIZED DISTRIBUTOR.

•WASTE AND OTHER MATERIAL SHOULD BE DISPOSED OF ACCORDING TO LOCAL

REGULATIONS AND PROCEDURES FOR WASTE DISPOSAL.

•CLEANING AND MAINTENANCE ARE NOT COVERED BY THE WARRANTY.

Содержание ALFA




























Результаты поиска

Содержание ALFA

Отзывы:

Похожие инструкции для ALFA

Бренды по названию

Популярные бренды

ITV ICE MAKERS ALFA, Техническое и сервисное руководство

Результаты поиска

Содержание ALFA

Отзывы:

Похожие инструкции для ALFA

Бренды по названию

Популярные бренды