ITV ICE MAKERS ALFA Скачать руководство пользователя страница 21

Страница: 21 / 27

NG DP

TECHNICAL SERVICE MANUAL

7. MAINTENANCE AND CLEANING INSTRUCTIONS

IMPORTANT!

**Maintenance and cleaning procedures as well as problems derived from failing to carry them

out are not covered by the warranty.

Proper maintenance is essential to obtain favorable ice quality and optimum functioning of unit.

Frequency depends on water quality and characteristics of room where unit is installed.

** Maintenance/cleaning procedures should take place at least once every six months. If

concentration of air pollutants is high, complete procedures on a monthly basis.

MAINTENANCE TABLE

ACTION

MONTHLY

BIMONTHLY SEMIANNUAL

ANNUAL

BIENNIAL

TIME

Air condenser
cleaning

30 minutes

Water condenser
cleaning

90 minutes

Injectors cleaning

30 minutes

Fabrication head filter
cleaning

30 minutes

Water circuit
cleaning

45 minutes

Sanitary cleaning

30 minutes

Water filter
cleaning/replacement

30 minutes

Stock deposit
cleaning

General unit cleaning

Essential

Depending on room characteristics

Depending on water quality

Carried out by owner

Maintenance and cleaning procedures as well as problems derived from failing to carry them out

ARE NOT COVERED BY THE WARRANTY

. Service personnel will invoice you for travel

expenses, time invested and materials required for maintenance and cleaning of unit.

Содержание ALFA




























Результаты поиска

Содержание ALFA

Отзывы:

Бренды по названию

Популярные бренды

ITV ICE MAKERS ALFA, Техническое и сервисное руководство

Результаты поиска

Содержание ALFA

Отзывы:

Бренды по названию

Популярные бренды