Installation, Operating and Maintenance Instruction
Model LM, LMN
LM ger/fr/eng
Page 51
Revision 02
Article No 771073101
Issue 01/2009
10. Faults - Causes and Solutions
The following notes on causes of faults and how to
repair them are intended as an aid to recognising the
problem. The manufacturer's Customer Service
Department is available to help repair faults that the
operator cannot or does not want to repair. If the
operator repairs or changes the pump, the design data
on the data sheet and chapter 2 of these Operating
Instructions should be particularly taken into account.
If necessary, the written agreement of the
manufacturer must be obtained.
D
is
ch
ar
ge
to
o
lo
w
D
is
ch
ar
ge
s
to
ps
a
fte
r
a
tim
e
H
ea
d
to
o
lo
w
H
ea
d
to
o
hi
gh
D
riv
e
m
ec
ha
ni
sm
o
ve
rlo
ad
ed
P
um
p
no
t r
un
ni
ng
q
ui
et
ly
T
em
pe
ra
tu
re
in
p
um
p
to
o
hi
gh
T
em
pe
ra
tu
re
in
s
ha
ft
se
al
in
g
to
o
hi
gh
T
em
pe
ra
tu
re
a
t t
he
b
ea
rin
g
to
o
hi
gh
P
um
p
le
ak
in
g
Le
ak
ag
e
ra
te
a
t s
ha
ft
se
al
in
g
to
o
hi
gh
Cause
Solution
■
Back-pressure too high
check facility for pollution, open discharge valve
reduce resistance in discharge pipe (e.g. clean filter if
necessary)
use larger impeller (note available motor power)
■
■
■
Back-pressure too low, discharge too low
throttle discharge valve
■
■
Speed too high
reduce speed
compare speed of motor with specified pump speed (rating
plate)
when adjusting speed (frequency transformer) check reference
value setting
■
■
Speed too low
increase speed (check available motor power)
compare speed of motor with specified pump speed (rating
plate)
when adjusting speed (frequency transformer) check reference
value settings
■
■
■
■
Flow too little
increase min. flow (open discharge valve, bypass)
■
Flow too big
reduce flow (throttle discharge valve)
■
■
Impeller diameter too big
use smaller impeller
■
■
Impeller diameter too small
use larger impeller (check available motor power)
■
■
■
■
Pump and/or pipes not completely filled with liquid
fill
vent
■
■
■
Pump or suction/intake pipe blocked
clean
■
■
Air pocket in pipeline
vent
improve course of pipe
■
■
■
■
■
Suction height too big / NPSH of system too small
increase liquid level and admission pressure
reduce resistance in the intake/suction pipe (change course
and rated width, open shut-off valves, clean filters)
■
■
■
Air being sucked in
increase liquid level
check if suction pipe is vacuum-tight
■
■
■
Air being sucked in through shaft sealing
clean sealing pipe
increase sealing pressure
replace shaft sealing
■
■
Direction of rotation is wrong
swap over two phases of power supply (to be done by an
electrician)
■
■
■
■
Inner components suffering from wear
replace worn parts
■
■
■
Density and/or viscosity of liquid handled is too high
seek assistance
■
■
Lines and roughness at shaft
replace parts
■
■
Deposits on mechanical seal
clean
replace mechanical seal if necessary
if necessary provide additional rinsing or quench
■
■
Impeller out of balance
remove blocks/deposits
replace impeller if broken or unevenly worn
check shafts to ensure that they are running true
■
■
■
■
■
Forces in pipeline too high (pump unit under strain)
change (support pipes, use compensators, etc.)
is foundation plate/frame properly cast in place?
■
Electricity supply not right (2-phase running)
check voltage of all phases
check cable connections and fuses
■
Sealing insufficient
tighten screws
replace sealing
■
■
Bearing damaged
replace
■
Relief fittings insufficient
clean relief openings in impeller
replace worn parts (impeller, split rings)
adjust in line with the system pressure/intake pressure given on
ordering
■
System-related vibrations (resonance)
seek assistance
Содержание VOGEL LM 100-160
Страница 69: ......
