ITT GOULDS PUMPS 3393 Скачать руководство пользователя | Manualshive

Страница: 20 / 125

background image

The 3393 is designed as a two-pole speed pump. There will be times when the pump will be operated at
variable speed. The 3393 can be operated between 2700 and 3600 rpm without reference to the factory.
At speeds above 3600 rpm and below 2700 rpm, a lateral critical speed analysis must be conducted by
the factory. Contact your local representative for pricing. In all cases it is imperative that the pump be
brought up to its minimum operating speed as quickly as possible. This ramp up time should not exceed
5 seconds.

RS

- Radial Suction configuration features radial suction

and discharge nozzles. The suction and discharge noz-
zles can be positioned either vertically or horizontally at
90

O

to either side. This design consists of two robust, fin-

ned bearing housings with traditional anti-friction bear-
ings and mechanical seals on each end of the pump.

ES

- End Suction configuration features an end suction

nozzle in conjunction with a radial discharge nozzle. The
suction end of the pump utilizes a product-lubricated
bearing eliminating the need for a second bearing hous-
ing and mechanical seal. Because of the positioning of
the sleeve bearing in the end suction casing, the suction
flange size is one size larger than the size for the radial
suction arrangement. The discharge nozzle can be posi-
tioned either vertically or horizontally at 90

O

to either

side.

3.3 General description i-ALERT

®

2 Equipment Condition Monitor

Description

The i-ALERT

®

2 Equipment Condition Monitor is a compact, battery-operated monitoring device that con-

tinuously measures the vibration and temperature of the pump power end. The i-ALERT

®

2 sensor uses

blinking red LEDs and wireless notification to alert the pump operator when the pump exceeds vibration
and temperature limits. This allows the pump operator to make changes to the process or the pump be-
fore a catastrophic failure occurs. The Condition Monitor is also equipped with a single green LED to in-
dicate when it is operational and has sufficient battery life. (i-ALERT

®

2 Bluetooth Equipment Condition

Monitor option available. The i-ALERT

®

2 monitor allows customers to identify potential problems before

they become costly failures. It tracks vibration, temperature and run-time hours and wirelessly syncs the
data with a smart phone or tablet the i-ALERT

®

2 mobile app. More information available on

More information available on

http://www.ittproservices.com/aftermarket-products/monitoring/i-alert2/i-

Current IOMs are available at

http://www.gouldspumps.com/en-us/tools

- and - resources/literature/

http://i-alert.com

or your local ITT Goulds Pumps Sales Rep.

3.4 Nameplate information

Important information for ordering

Every pump has a nameplate that provides information about the pump. The nameplate is located on the
pump casing.

When you order spare parts, identify this pump information:

•

Model

3.3 General description i-ALERT®2 Equipment Condition Monitor

18

Model 3393 Installation, Operation, and Maintenance Manual

«
...
18
19
20
21
22
...
»

Содержание GOULDS PUMPS 3393






























































































































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3393

Бренд: Davey Страницы: 8

Бренд: Davey Страницы: 8

Бренд: Davey Water Products Страницы: 4

Бренд: SAER Elettropompe Страницы: 76

Бренд: EBARA Страницы: 22

Бренд: VARISCO Страницы: 72

Бренд: Quincy Compressor Страницы: 122

Бренд: York Страницы: 84

Бренд: York Страницы: 90

Power Vent Raytherm 2100

Бренд: Raypak Страницы: 2

EVERPURE CONSERV LT-S

Бренд: Pentair Страницы: 20

Бренд: All-Flo Страницы: 28

Бренд: Quooker Страницы: 20

Clean Jet 800 Plus + Kit

Бренд: T.I.P. Страницы: 140

RESIDENTIAL GAS FIRED WATER HEATERS

Бренд: Giant Страницы: 8

Бренд: Ingersoll-Rand Страницы: 1

Бренд: T.I.P. Страницы: 72

Бренд: Campbell Hausfeld Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды