background image

12

ØD

k

min

k

max

a

b

M

120

94

12

120

∅34

Drive Set

[mm]

8 80 D80/D34

⌀ D

12-45

a

12

b

106

k

 min

48.5

max

63.7

Coupling half that accommodates the drive shaft

Coupling Housing with hole (that can be sealed) to allow an Allen key through 

to generate the necessary clamping force on the drive shaft.

Connecting Drive Set 8 80 D80/D34 – 0.0.668.04

Drive Set 8 80 D80/D34 is used to connect any drive to Linear Unit LRE 8 

D25 ZU 80 R25.
The prepared coupling fits the drive shaft and transmits drive torque without 

backlash.

Hexagon Socket Head Cap Screws DIN 912 M8x100 are supplied with the 

Drive Set for this purpose and are screwed through the housing of the Drive 

Unit and into the Coupling Housing of the Drive Set.
Tightening torque: T = 25 Nm
Machine the drive casing or Adapter Plate according to the requirements of 

the motor or gearbox you are using and then screw it to the motor or gearbox. 

Take the coupling half that is to be connected to the drive shaft and drill a hole 

in it to match the drive shaft then connect the coupling half and the shaft.

The torques transferred by the clamp connection factor in the maximum 

mating play for shaft fits: Shaft k6 / hole H7.

Force is transferred from the coupling to the drive shaft by means of frictional 

resistance. The Shaft and the hole in the coupling hub must be degreased and 

cleaned to ensure the frictional resistance is effective. Hexagon Socket Head 

Cap Screws must be secured against working loose.

Adapter plate

Содержание LRE 8 D25 ZU 80 R50

















Отзывы: