Itamar Medical WatchPAT Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 58

Itamar Medical WatchPAT Скачать руководство пользователя страница 50

WatchPAT

™

ONE System

45

Operation Manual

APPENDIX C: MANUFACTURING DECLARATIONS ACCORDING TO
IEC 60601-1 & 60601-1-2

Notes

• The WatchPAT requires special precautions with regards to electromagnetic compatibility.
• Certain types of mobile telecommunication devices are likely to interfere with the WatchPAT.
• The recommended separation distances in this section must therefore be complied with.
• The WatchPAT must not be used near or on top of another device. If this cannot be avoided, it is necessary –

before clinical use – to check the equipment for correct operation under the conditions of use.

• The use of accessories other than those specified or sold by Itamar Medical as replacement parts may have the

consequence of increasing the emissions or decreasing the immunity of the unit.

• The WatchPAT device does not have essential performance according to IEC 60601-1-2.
• WARNING: Portable RF communications equipment (including peripherals such as antenna cables and

external antennas) should be used no closer than 30 cm (12 inches) to any part of the WatchPAT, including
cables specified by the manufacturer. Otherwise, degradation of the performance of this equipment could result.

Electromagnetic Compatibility

Electromagnetic Emissions



WatchPAT is intended for use in the electromagnetic environment specified in the following tables 1, 2, 4 and
6 below.

• The user must ensure that it is used in such an environment.
• No unexpected behavior was detected during immunity testing and performance was met.

Table 1

– from IEC 60601-1-2:2014

Guidance and manufacturer's declaration

– electromagnetic emissions – WatchPAT

The

WatchPAT

is intended for use in the electromagnetic environment specified below; The customer or the user of the

WatchPAT

should assure that it is used in such an environment.

Emissions test

Compliance

Electromagnetic environment - guidance

RF emissions

CISPR 11

Group 1

The

WatchPAT

uses RF energy for internal function

and for BLE

(4dbm) transmissions.

Therefore, its RF emissions are very low and are not likely to cause any
interference in nearby electronic equipment.

RF emissions

CISPR 11

Class B

The

WatchPAT

is suitable for use in all establishments, including

domestic establishments and those directly connected to the public
low-voltage power supply network that supplies buildings used for
domestic purposes.

Harmonic Emissions

IEC 61000-3-2

Not applicable

Voltage fluctuations/

flicker emissions

IEC 61000-3-3

Not applicable

«
...
48
49
50
51
52
...
»

Содержание WatchPAT



























































Отзывы:

Нет отзывов