background image

equipped). Disconnect accelerator control cable from carburetor.

         7) Disconnect starter motor wiring. Disconnect temperature

sensor, oil pressure switch and distributor wiring. Disconnect hose

at vacuum switch (if equipped). Disconnect temperature switch and

ground wire from rear of intake manifold (if equipped).

         8) Disconnect hose from solenoid valve (if equipped).

Disconnect EFE heater wiring, carburetor solenoid and choke wiring.

Disconnect back-up light switch and transmission switch wiring at

rear of engine.

         9) Disconnect ECS hose from engine oil pan (if equipped).

Remove right engine mount nut. Raise engine slightly and remove left

engine stop plate. On 4WD models, separate engine from transmission.

         10) Discharge A/C system and disconnect A/C compressor lines

(if equipped). Disconnect radiator hoses, fan shroud, radiator and

fan blade assembly. Remove gearshift lever assembly from passenger

compartment. Remove parking brake cable return spring. Disconnect

parking brake cable.

         11) Remove drive shaft. Remove clutch cable return

spring. Disconnect clutch cable and remove cable from engine holder.

Remove front exhaust pipe bracket from transmission. Disconnect side

exhaust pipes. Remove front pipe.

         12) Disconnect speedometer cable. Raise engine slightly.

Remove rear engine mount bolts. On 4WD models, remove engine from

vehicle. On all other models, remove engine and transmission from

vehicle.

         Installation

         To install, reverse removal procedure.

         Removal (Impulse)

         1) Disconnect battery cables. Disconnect relay box cables

(if equipped). Disconnect headlight drive motor wiring. Remove hood

strut. Scribe hinge positions on hood and remove hood. Remove lower

engine cover. Drain crankcase oil and cooling system. Remove lower

and upper radiator hoses. Disconnect transmission oil cooler line (if

equipped).

         2) Discharge A/C system. Disconnect receiver-drier line.

Disconnect A/C compressor line at condenser. Remove A/C compressor

and set aside. Remove air duct-to-cylinder head cover/turbocharger

(if equipped). Remove throttle body/intercooler air duct hose (if

equipped). Disconnect accelerator cable at throttle body. On turbo

models, disconnect air duct-to-intercooler hose.

         3) Disconnect injection pipe-to-pressure regulator hose.

Disconnect fuel hose from fuel injection line at rear of engine.

Disconnect canister purge hoses from vacuum chamber and at 3-way

connector. Disconnect vacuum switching valve hoses from vacuum

chamber and at 3-way connector.

         4) Disconnect wiring from fender skirt to cylinder head.

Remove coil high tension wire. On models with digital instrument

panel, disconnect boost sensor wiring and vacuum hose.

         5) Disconnect oil pressure sending unit, oil pressure switch

and coolant temperature sensor wiring. Disconnect knock sensor and

I-TEC wiring. Disconnect crankshaft position sensor wiring at

distributor. Disconnect starter wiring and engine-to-rear crossmember

ground cable.

         6) Remove right engine mount nut. Remove air intake duct at

front of engine. Remove radiator reservoir hose. Disconnect

alternator and oxygen sensor wiring. Disconnect cruise

control-to-vacuum chamber hose. Disconnect automatic transmission

control wiring (if equipped).

         7) Disconnect power brake unit vacuum hose from intake

manifold. Disconnect heater hoses. Remove heat shield from left

engine mount and remove mount bolt. Disconnect power steering lines.

Содержание Trooper II 1986


























Отзывы: