Isuzu AU-4LE1T Скачать руководство пользователя страница 111

Страница: 111 / 126

106

Symptom Cause

Action

Damaged packing.

Change packing.

Fuel leakage.

Improper installation or tightening.

Reinstall or retighten air bleeder plug.

Too much
injection
amount.

Injection pump misadjustment.

◎

Excessive
fuel
consumption.

Excessive
mechanical
loads.

Operation

Check the mechanical loads.

Clogged air cleaner.

Clean or change element.

Nozzle damage.

◎

Nozzle misadjustment.

Make a readjustment.

Injection timing failure.

◎

Injection amount misadjustment.

◎

Improper fuel.

Use fuel in this instruction manual.

Much black
smoke.

EGR valve fixing. (Open position.)

◎

Oil coming up or down.

Change oil.

Water mixing in fuel.

Remove water.

Low compression pressure.

◎

Injection timing failure.

◎

Improper
exhaust.

Much white
smoke.

Low coolant temperature.

Inspect or change thermostat.

Crack in battery body.

Change battery.

Battery
overdischarge.

Low
electrolyte
level.

Natural consumption.

Change battery.

Содержание AU-4LE1T































































































































Результаты поиска

Содержание AU-4LE1T

Отзывы:

Похожие инструкции для AU-4LE1T

Бренды по названию

Популярные бренды

Isuzu AU-4LE1T, Руководство по обслуживанию

Результаты поиска

Содержание AU-4LE1T

Отзывы:

Похожие инструкции для AU-4LE1T

Бренды по названию

Популярные бренды