Isuzu AU-4LE1T Скачать руководство пользователя страница 108

Страница: 108 / 126

103

Symptom Cause

Action

Crack in injection pipe.

◎

Injection nozzle failure.

◎

Engine stop solenoid return failure.

◎

Uneven compression pressure between cylinders.

◎

Incorrect control lever adjustment.

◎

Governor interior malfunction.

◎

Governor spring deteriorated.

◎

Air in the fuel system.

Bleed air.

Clogged fuel filter element.

Remove water and change element.

Piping failure (squeezed, etc.) in the fuel system.

◎

Uneven fuel injection amount between plungers.

◎

Incorrect valve clearance adjustment.

Make a readjustment.

Deteriorated valve spring.

Change valve spring.

Unstable engine running.

Engine control restriction or seizure.

◎

Insufficient coolant amount.

Replenish.

Fan belt slippage.

Make an adjustment.

Thermostat malfunction.

Change thermostat.

Radiator filler cap malfunction.

Change radiator filler cap.

Engine overheat.

Cooling system interior fouled.

Clean cooling system interior.

Содержание AU-4LE1T































































































































Результаты поиска

Содержание AU-4LE1T

Отзывы:

Похожие инструкции для AU-4LE1T

Бренды по названию

Популярные бренды

Isuzu AU-4LE1T, Руководство по обслуживанию

Результаты поиска

Содержание AU-4LE1T

Отзывы:

Похожие инструкции для AU-4LE1T

Бренды по названию

Популярные бренды