background image

SERVICE INFORMATION  00 – 9

4. EXCESSIVE FUEL CONSUMPTION

Checkpoint

Possible cause

Correction

Fuel system

Fuel leakage

Repair or replace the fuel system
related parts

Air cleaner

Clogged air cleaner element

Clean or replace the air cleaner
element

Idling speed

Poorly adjusted idling speed

Adjust the idling speed

Injection nozzle

Injection nozzle injection starting pressure
too low
Improper spray condition

Adjust or replace the injection nozzle

Fuel injection timing

Fuel injection timing improperly

Adjust the fuel injection timing

Injection pump

Defective Delivery valve resulting is fuel
drippage after fuel injection

Replace the delivery valve

Valve clearance

Valve clearance improperly adjusted

Adjust the valve clearance

Compression pressure

Blown out cylinder head gasket.  Worn
cylinder liner.
Piston ring sticking

Replace the related parts

Valve spring

Valve spring weak or broken

Replace the valve spring

5. EXCESSIVE OIL CONSUMPTION

Checkpoint

Possible cause

Correction

Engine oil

Engine oil unsuitable
Too much engine oil

Replace the engine oil
Correct the engine oil level

Oil seal and gasket

Oil leakage from the oil seal and/or the
gasket

Replace the oil seal and/or the gasket

Air breather

Clogged air breather

Clean the air breather

Intake and exhaust
valve

Worn valve stems and valve guides

Replace the intake and exhaust
valves and the valve guides

Содержание 4JB1





























































Отзывы: