manualshive.com logo in svg

Isuzu 4JB1, Информация о сервисе, Страница: 42 / 60

Поделиться
Скачать
Isuzu 4JB1 Скачать руководство пользователя страница 42

00 – 44

  

SERVICE INFORMATION

Drive Belt Adjustment

Depress the drive belt mid portion with a 98N (10 kg/22
lb) force.

Drive Belt Deflection

mm (in)

                                                                                                                   

10 (0.39)

                                                                                                                   

Check the drive belt for cracking and other damage.

1. Crankshaft damper pulley
2. Generator pulley
3. Cooling fan pulley
4. Oil pump pulley or idler pulley
5. Compressor pulley or idle pulley

Cooling Fan Pulley Drive Belt

Fan belt tension is adjusted by moving the generator.

Depress the drive belt mid portion with a 98N (10 kg/22
lb) force.

1. Crankshaft damper pulley

2. Generator pulley

3. Cooling fan pulley

Compressor Pulley Drive Belt

Move the idler pulley as required to adjust the compressor
drive belt tension.

If the vehicle is equipped with power steering, move the
oil pump as required.

Depress the drive belt mid portion with a 98N (10 kg/22
lb) force.

Belt Deflection

mm (in)

                                                                                                                   

14 - 17 (0.55 - 0.67)

                                                                                                                   

1. Crankshaft damper pulley

2. Oil pump pulley or idler pulley

Power Steering Oil Pump Pulley Drive Belt

Move the oil pump as required to adjust the oil pump drive
belt tension.

On air conditioner equipped models, both drive belts
pulley must always be replaced as a set.

Depress the drive belt mid portion with a 98N (10 kg/22
lb) force.

Belt Deflection

mm (in)

                                                                                                                   

14 - 17 (0.55 - 0.67)

                                                                                                                   

1. Crankshaft damper pulley

2. Oil pump pulley

3. Compressor pulley or idler pulley

0043-1.tif

0043-2.tif

0043-3.tif

0043-4.tif

Содержание 4JB1





























































Отзывы:

Нет отзывов