Isuzu 4JB1 Скачать руководство пользователя страница 4

Страница: 4 / 60

00 – 6

SERVICE INFORMATION

GLOW PLUGS ARE NOT RECEIVING POWER (Cont’d)

Checkpoint

Possible cause

Correction

Defective glow plug relay
The glow plug relay does not turn on after the
starter switch is moved from the “OFF”
position to the “ON” position

Replace the glow plug relay

Defective quick-on start timer

Replace the quick-on start timer

Defective glow plug relay wiring harness

Repair or replace the wiring harness

Glow plug indicator
light turns on for 3.5
seconds

Defective fusible link or wiring harness
The glow plug relay turns on when the starter
switch is moved from the “OFF” position to
the “ON” position

Replace the fusible link or the wiring
harness

2. UNSTABLE IDLING

Checkpoint

Possible cause

Correction

Idling system

Idling improperly adjusted

Adjust the idling

Fast idling speed

Defective fast idling speed control device

Repair or replace the fast idling speed
control device

Accelerator control
system

Accelerator control system improperly
adjusted

Adjust the accelerator control system

Fuel system leakage or blockage

Repair or replace the fuel system

Air in the fuel system

Bleed the air from the fuel system

Fuel system

Water particles in the fuel system

Change the fuel

Fuel filter

Clogged fuel filter element

Replace the fuel filter element or the
fuel filter cartridge

Fuel feed pump

Defective fuel feed pump

Repair or replace the fuel feed pump

Injection nozzle sticking

Replace the injection nozzle

Injection nozzle

Injection nozzle injection starting pressure
too low
Improper spray condition

Adjust or replace the injection nozzle

Injection pump

Defective delivery valve resulting in fuel
drippage after fuel injection

Replace the delivery valve

Содержание 4JB1





























































Результаты поиска

Содержание 4JB1

Отзывы:

Похожие инструкции для 4JB1

Бренды по названию

Популярные бренды

Isuzu 4JB1, Информация о сервисе

Результаты поиска

Содержание 4JB1

Отзывы:

Похожие инструкции для 4JB1

Бренды по названию

Популярные бренды