Isuzu 4JB1 Скачать руководство пользователя страница 47

Страница: 47 / 60

SERVICE INFORMATION 00 – 49

COMPRESSION PRESSURE MEASURE-
MENT

1. Start the engine and allow it to idle until the coolant

temperature reaches 70 - 80°C (158 - 176°F).

2. Remove the following parts.

Glow plugs

Fuel cut solenoid connector

QOS (Quick-On Start System) fusible link wire at
the connector.

3. Set the adapter and compression gauge to the No. 1

cylinder glow plug hole.

Compression Gauge

(with Adapter): 5-8840-2008-0 (J-29762)

Adapter: 5-8531-7001-0

4. Turn the engine over with the starter motor and take

the compression gauge reading.

Compression Pressure at 200 rpm

kPa (Kg/cm

/psi)

Standard

Limit

4JB1

3,038 (31/441)

2,157 (22/313)

4JG2

3,334 (34/484)

2,452 (25/356)

5. Repeat the procedure (Steps 3 and 4) for the

remaining cylinders.

If the measured value is less than the specified limit,
refer to “Troubleshooting” in this Manual.

QUICK-ON START II SYSTEM
(4JB1 / 4JB1T / 4JB1TC only)

Quick-On Start System Inspection Procedure

1. Disconnect the thermo-sensor connection on the

thermostat outlet pipe.

2. Turn the starter switch to the “ON” position.

If the Quick-On Start II System is operating properly,
the glow relay will make a clicking sound within 15
seconds after the starter switch is turned on.

3. Measure the glow plug terminal voltage with a circuit

tester immediately after turning the starter switch to
the “ON” position.

Glow Plug Terminal Voltage

Approx. 11

0048-1.tif

0048-2.tif

0048-3.tif

0048-4.tif

Содержание 4JB1





























































Результаты поиска

Содержание 4JB1

Отзывы:

Похожие инструкции для 4JB1

Бренды по названию

Популярные бренды

Isuzu 4JB1, Информация о сервисе

Результаты поиска

Содержание 4JB1

Отзывы:

Похожие инструкции для 4JB1

Бренды по названию

Популярные бренды