iSP Technologies THETA PRO DSP Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 25

iSP Technologies THETA PRO DSP Скачать руководство пользователя страница 3

Quick Start

Refer to the Figures shown for the hardware drawings which show the locations of
the switches, knobs, and jacks when reading the following, or even better, just look
at your unit.

1.

Connect  the  guitar  to  the  IN  jack,  connect  the  STAGE  OUT  jack(s)  to  a  power
amp such as the ISP Stealth which is connected to a guitar speaker cabinet, OR
connect  the  DIRECT  OUT  jacks  to  the  input  of  a  mixer,  OR  connect  the
PHONES  jack  to  headphones  or  earbuds  (or  connect  all  three).  With  a  mono
system,  the  output(s)  can  be  set  to  mono  in  the  global  parameters  later.  The
STAGE OUT jacks can be connected to a conventional guitar amplifier, but this
will  not  yield  optimum  results,  since  most  guitar  amps  will  further  shape  and
distort the sound.

2.

Connect the supplied 9V AC power adaptor to wall power, then to the POWER
input on the Theta Pro. The unit will power up and recall Preset 1. Pressing the
RECALL 1 switch will display the Preset 1 title.

3.

With  the  Preset  title  displayed,  adjust  the  INPUT  LEVEL  control  on  the  back
panel so that the LEVEL 0 LED (red) just flashes when playing hard, then back
off  the  INPUT  LEVEL  control  slightly  so  that  the  0  LED  does  not  light.  Short,
infrequent flashes of the red 0 LED are generally not audible.  Adjust the STAGE
OUT LEVEL or PHONES LEVEL controls to taste. The DIRECT OUT levels can
be  controlled  by  the  global  DIRECT  TRIM  parameter  which  affects  all  presets,
and  by  the  OUTPUT  LEVEL  parameter  within  each  preset,  which  affects  all
outputs, but is the level specific to each preset. Note that the LEVEL LEDs only
display  the  raw  input  level  when  the  preset  or  song  titles  are  displayed
(FUNCTION  turned  fully  counterclockwise).  If  any  other  parameters  are
displayed,  the  LEVEL  LEDs  will  display  the  maximum  of  the  4  output  DAC
(Digital to Analog Converter) levels.

«
1
2
3
4
5
...
»

Содержание THETA PRO DSP


























Отзывы:

Нет отзывов