Iseo IS 9100 Скачать руководство пользователя страница 30

Страница: 30 / 36

Error

Possible cause

Remedy

During the installation:

It is difficult to manually

open the door and the

closing movement takes

place at a high speed.

The connector of the braking circuit is

in the incorrect position.

The connector must be positioned correctly depending

on the arms assembly used.

See page 17 point 5.9.

The teach-in run cannot be

started.

The program switch is in the incorrect

position.

Turn the program switch into the "OFF" position.

The signal shutdown

drive function (4/4a) is active.

Test the wiring of the smoke detector or the stop signal

on 4/4a.

The internal/external

program switch does not

work or incorrectly

The parameter program switch type is

incorrectly set.

The type used must be correctly set as parameter

program switch type.

The cable of the internal program

switch is not attached.

Test the cable and connect, if necessary.

Connection error or switch defect.

The wiring and function of the switch must be tested.

The door opens

automatically but closes

only after a long time or

not at all.

The hold-open time is too long.

Reduce the hold-open time.

The program switches in the Permanent

Open position.

Switch the program switch.

There is a signal from the safety sensor

on the opposite hinge side and it

prevents the closing.

The signals of the safety sensors will be displayed for

the diagnosis directly with the 2 decimal

points of the LED display on the user

interface.

In case of a detection, the respective

decimal point will light. The wiring and function of

the system must be tested. If the LED at the top left

flashes, the wall suppression will be active. There is no

error.

There is a signal from a connected

activator that prevents the closing.

The wiring of the connected activator must be tested.

A normally open contact is to be used in all cases.

The signal input 57/57a may be operated with external

voltage. Remove the signal lines 35, 57, 42 and 41 one

after another in order to localize the error.

The speeds differ strongly

from the set parameters.

The teach-in run was performed with a

warm motor and the door panel weight

was therefore incorrectly determined.

Repeat the teach-in run with the motor cold.

LED red
LED yellow

Power switch

LED green

IS 9100

—

30 ISEO

Содержание IS 9100





































Результаты поиска

Содержание IS 9100

Отзывы:

Похожие инструкции для IS 9100

Бренды по названию

Популярные бренды

Iseo IS 9100, Инструкция по монтажу и пусконаладке

Результаты поиска

Содержание IS 9100

Отзывы:

Похожие инструкции для IS 9100

Бренды по названию

Популярные бренды