iseg EHQ 1 Series Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 46

background image

1 General description

The EHQ´s are one channel high voltage supplies in a 3U Eurocard Chassis, 8TE wide. The units offers manual control via the
front panel and operation via USB and RS232 interface (optional: CAN Bus interface). The interface control supports more
functionality then the manual control.
The high voltage supplies features high precision output voltage and very low ripple, even under full load. Separate hardware
switches allow to put voltage and current limits in 10%-steps. The INHIBIT input protects sensitive devices. Additionally, a
maximum output current can be specified via the interface. The high voltage source is protected against overload and short
circuit. The output polarity can be switched over. The HV-GND is connected to the chassis and the powering GND.

EHQ High Voltage Power Supply series | Last changed on: 11.05.2020 |

www.iseg-hv.com

9/46

«
...
7
8
9
10
11
...
»

Содержание EHQ 1 Series















































Отзывы:

Нет отзывов

Похожие инструкции для EHQ 1 Series

Бренд: unicore Страницы: 25

Бренд: unicore Страницы: 24

Бренд: Daikin Страницы: 38

Бренд: Daikin Страницы: 2

Бренд: Daikin Страницы: 148

Бренд: Daktronics Страницы: 52

Бренд: Waeco Страницы: 20

Бренд: Z-Wave Страницы: 56

Бренд: Harmonic Drive Страницы: 85

Бренд: vacuubrand Страницы: 12

Бренд: Vacon Страницы: 47

Бренд: Vacon Страницы: 40

Бренд: OEM Страницы: 8

Бренд: ABB Страницы: 102

Бренд: Bender Страницы: 28

Бренд: Hirschmann Страницы: 48

Бренд: Nibe Страницы: 84

Бренд: IBC control Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды