manualshive.com logo in svg

Ironman4x4 BBR085E, Руководство по установке

Поделиться
Скачать
Ironman4x4 BBR085E Скачать руководство пользователя страница 3

Page 3 of 18

BBR085E

Installation Guide

©Copyright 2022 Ironman 4x4 Pty Ltd. No part of this publication may be reproduced or replicated without the prior written consent of Ironman 4x4 Pty Ltd

•   Ironman 4x4 recovery points are FEA Tested during design and Destruction tested    
 

during development to establish the Working Load Limits. (WLL) 

•   Ironman 4x4 recovery points have been designed as a matching pair, supplied in  

 

 

right, and left sides for vehicle specific fitment. 

•   Ironman 4x4 include specific mounting hardware to ensure correct fitment to your    
 

4WD. The correct fitment of these components is critical for your safety.

•   Do not use this recovery point for any other vehicle make or model other than the one  
 

intended and specified by Ironman 4x4. 

•   Do not alter or modify the recovery point in any way. Doing so may compromise the    
 

points strength and integrity. 

•   Ensure that bolts are tightened to specified torque. 
•   Don’t remove warning labels from the recovery point. (Some recovery points require   
 

the warning labels to be installed, these must be installed) 

•   It is advised to use an equalizing or bridle strap, failure to do so correctly can result in  
 

recovery point fatigue and bending and voiding your warranty. 

•   Never use a single recovery point combined with a side load pull. 
•   Recovery Points are designed for a straight-line pull, by pulling on and angle/   

 

 

sideways pull may result in a reduction of the WLL.

Page 3 of 18

©Copyright 2022 Ironman 4x4 Pty Ltd. No part of this publication may be reproduced or replicated without the prior written consent of Ironman 4x4 Pty Ltd

WARNING

Installation Guide

Содержание BBR085E



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды