Ironman4x4 BBR085E Скачать руководство пользователя страница 15

Страница: 15 / 18

Page 15 of 18

BBR085E

Installation Guide

36.

Connect/wire up fog lights, light bars

(if applicable).

Refer to wiring diagram on page 17.

NOTE:

Connect main parking sensor

plug if vehicle is equipped with Front

sensors.

37.

Install the protection plate bracket

N#34 2x (M10x1.5x45mm t-bolt,

washer, nut) to Chassis pedestal (the

mount is the aero mounting pedestal)

using the inner chassis rail as shown.

Repeat on the other side.

38.

Install centre protection plate with

black M8 bolts provided. N#29

4X (M8x1x25mm) and 2 x N#36

(M12x1.5x45mm bolt, washer, nut)

Bolt the UBP through the lower cradle

mount and then to chassis.

35.

Note: This bar has been supplied with

Taptite Bolts. (These don’t require a

washer or nut to mount)

Installation: The M10 taptite bolt

supplied requires a 9mm hole. Drill

the 9mm hole, then add lock tight to

thread of the Taptite. Using a rattle

GUN, bolt Taptite up. The Taptite will

cut its own thread.

39.

Install both wing protection plates with

black M8 bolts provided. N#29 6X

(M8x1x25mm).

Содержание BBR085E



















Результаты поиска

Содержание BBR085E

Отзывы:

Бренды по названию

Популярные бренды

Ironman4x4 BBR085E, Руководство по установке

Результаты поиска

Содержание BBR085E

Отзывы:

Бренды по названию

Популярные бренды