Ironman Fitness 5214 Скачать руководство пользователя

Страница: 26 / 29

REMOTE CONTROL

CONTROLLER PANEL

REMOTE CONTROL AND CONTROLLER OPERATION

1. By default setting, when turned on, the temperature is set to 140 degrees F (60 degrees C), and

timer is set to 40 minutes. This will ensure the far infrared foam bed heats up as quickly as

possible. Adjust the temperature down to your desire setting after preheat. Set Low Heat at

100-110, Medium Heat at 120-130, or High Heat at 130-140 degrees F.

2. The normal preheat time is 15-20 minutes, under room temperature at 68-77degrees F

(20-25 degrees C).

3. Both Remote Control and Controller can be used to set desired temperature and time.

4. The LED on the Controller reads out the current temperature and remaining time.

5. The Remote Control will function either aiming directly to the Controller or to the wall/ceiling in

the room when using the table.

6. The Remote Control comes with a Velcro strap. Pull apart to open the Velcro strap for two

layers. Remove the liner away from the short layer, choose adhesive backing for bonding to

the back of the Remote Control. Remove the liner away from the long layer, choose adhesive

backing for bonding to the inversion table where it is easy reach by hand, such as

Front U-Frame. Attach the Remote Control to it when not in use. Or simply drop it into the

mesh pocket of the right side cover for storage.

Precautions

Plug must be plugged into an appropriate outlet that is properly installed. Improper connection can

result in the risk of electric hazard.

A typical indoor extension cord may used to reach a desired electrical outlet.

Set the temperature and time to a comfortable level.

Far Infrared Foam Bed Operation

Plug the unit into the outlet with the “

POWER

” light off before starting it and use the

ON/OFF

switch to

turn on the cushion. After starting the unit, the digital light of temperature displays the set

temperature as 140 degrees F (60 degrees C). The temperature can be changed by pressing the

“

∧

” or “

∨

” button to increase or decrease the temperature. The digital light of time displays the set

time is 59 minutes. Timer can be changed by pressing the “

” or “

” button to increase or decrease

time. After 5 seconds, the digital light in temperature flashes 2 times and then returns to display the

current temperature of far infrared foam bed. When pressing the button “

∧

” or “

∨

” again, it will

change to display the “set temperature” and can be set to desired temperature.

Press the

℃

℉

button to switch the display between Centigrade and Fahrenheit.

Buzzer will beep when time counts down to 0 or the temperature reaches your set temperature.

After using the unit, turn off the

ON/OFF

switch, and unplug the power cable.

Содержание 5214






























Результаты поиска

Содержание 5214

Отзывы:

Похожие инструкции для 5214

Бренды по названию

Популярные бренды

Ironman Fitness 5214, Руководство пользователя

Результаты поиска

Содержание 5214

Отзывы:

Похожие инструкции для 5214

Бренды по названию

Популярные бренды